化工进展 ›› 2018, Vol. 37 ›› Issue (04): 1529-1535.DOI: 10.16085/j.issn.1000-6613.2017-1263

• 材料科学与技术 • 上一篇    下一篇

微波强化烧结制备铁钴基金刚石锯片刀头

高冀芸1,2,3,4, 刘晨辉2,4, 王访1,4, 杨黎5, 贾丽娟4, 段开娇4, 刘天成1,2,3,4, 郭雨4   

  1. 1 云南省跨境民族地区生物质资源清洁利用国际联合研究中心, 云南 昆明 650500;
    2 云南省高校民族地区资源清洁转化重点实验室, 云南 昆明 650500;
    3 民族地区矿产资源综合利用重点实验室, 云南 昆明 650500;
    4 云南民族大学化学与环境学院, 云南 昆明 650500;
    5 昆明理工大学冶金与能源工程学院, 云南 昆明 650093
  • 收稿日期:2017-06-23 修回日期:2017-07-30 出版日期:2018-04-05 发布日期:2018-04-05
  • 通讯作者: 刘天成,教授,研究方向为化工过程、材料烧结。
  • 作者简介:高冀芸(1989-),女,硕士,助教。
  • 基金资助:
    国家自然科学基金(51604134,51568068)、云南民族大学校内青年基金科研项目(2017QN06)、云南省应用基础研究计划青年项目(201701YE00021)、国家国际科技合作项目(2015DFR50620)、云南省教育厅科学研究基金(2016ZZX040)及云南民族大学大学生创新创业训练计划(2017JWC-DC-39)项目。

Fabrication of the diamond sawblade bits with Fe-Co metallic matrix by microwave strengthened sintering

GAO Jiyun1,2,3,4, LIU Chenhui2,4, WANG Fang1,4, YANG Li5, JIA Lijuan4, DUAN Kaijiao4, LIU Tiancheng1,2,3,4, GUO Yu4   

  1. 1 Joint Research Centre for International Cross-border Ethnic Regions Biomass Clean Utilization in Yunnan, Kunming 650500, Yunnan, China;
    2 Key Laboratory of Resource Clean Conversion in Ethnic Region, Education Department of Yunnan, Kunming 650500, Yunnan, China;
    3 Key Laboratory of Comprehensive Utilization of Mineral Resources in Ethnic Regions, Kunming 650500, Yunnan, China;
    4 College of Chemistry and Environment, Yunnan MinZu University, Kunming 650500, Yunnan, China;
    5 Faculty of Metallurgical and Energy Engineering, Kunming University of Science and Technology, Kunming 650093, Yunnan, China
  • Received:2017-06-23 Revised:2017-07-30 Online:2018-04-05 Published:2018-04-05

摘要: 采用微波烧结技术制备了低钴型Fe-Co基金刚石锯片刀头,利用圆柱谐振腔微扰法电磁特性测试系统评价了配方物料压坯的吸波特性,并结合物料在微波场中的升温特性设计了可行的微波烧结制度。采用SEM、致密度和硬度测试对比研究了微波烧结和常规烧结所得样品的微结构信息和力学性能。结果表明,对于低钴高铁型配方,在850℃下微波烧结获得的样品,其相对致密度和硬度即可分别达到96.63%和99.4HRB,微波烧结在最大升温速率为32.5℃/min时能保证烧结体组织均匀。与常规烧结方法相比,在获得同等级力学性能的前提下,微波强化烧结可将温度降低至900℃以下,显著缩短了烧结总时间,在金属基金刚石工具刀头烧结方面表现出良好的应用前景。

关键词: 粉体, 烧结, 热传导, 力学性能

Abstract: The iron-cobalt(Fe-Co) metallic matrix diamond sawblade bits with low cobalt were successfully fabricated through microwave sintering. The microwave-absorbing characteristic of the designed recipe compacts were estimated on an electromagnetic characteristic test system by applying the cylindrical resonant cavity perturbation method. The microwave sintering procedure was designed according to the heating characteristics of the material in the microwave field. The microstructure information and mechanical properties were investigated and compared by using scanning electron microscope(SEM),relative density and hardness tests in case of the microwave and conventional sintering method. The result showed the relative density and hardness reached 96.63% and 99.4HRB respectively for the low cobalt samples sintered at 850℃. In addition,the microstructure was still uniform when the samples was under microwave sintered at the temperature rate of 32.5℃/min. Compared with the conventional sintering method,on the premise of comparative mechanical properties,microwave strengthening sintering can significantly shorten the total sintering time and decrease the sintering temperature below 900℃ to achieve similar mechanical properties of the product. The microwave heating technology shows an excellent application prospect in the field of the strengthen sintering for the metallic matrix diamond tool bits.

Key words: powders, sintering, heat conduction, mechanical properties

中图分类号: 

京ICP备12046843号-2;京公网安备 11010102001994号
版权所有 © 《化工进展》编辑部
地址:北京市东城区青年湖南街13号 邮编:100011
电子信箱:hgjz@cip.com.cn
本系统由北京玛格泰克科技发展有限公司设计开发 技术支持:support@magtech.com.cn