化工进展 ›› 2019, Vol. 38 ›› Issue (12): 5306-5313.DOI: 10.16085/j.issn.1000-6613.2019-0848

• 化工过程与装备 • 上一篇    下一篇

改进型框式组合桨搅拌釜内流场特性

周勇军(),袁名岳,孙存旭   

  1. 南京工业大学机械与动力工程学院,江苏 南京 211816
  • 收稿日期:2019-05-26 出版日期:2019-12-05 发布日期:2019-12-05
  • 通讯作者: 周勇军
  • 作者简介:周勇军(1969—),男,副教授,研究方向为流体机械技术开发应用。E-mail:zhouyj@njtech.edu.cn
  • 基金资助:
    国家自然科学基金(51775262);江苏省高校自然科学基金(16KJA400001)

Investigating on flow field in stirred tank equipped with improved frame type combined impellers

Yongjun ZHOU(),Mingyue YUAN,Cunxu SUN   

  1. College of Mechanical and Power Engineering, Nanjing Tech University, Nanjing 211816, Jiangsu, China
  • Received:2019-05-26 Online:2019-12-05 Published:2019-12-05
  • Contact: Yongjun ZHOU

摘要:

对5m3树脂反应釜及釜内改进型框式-二斜叶双层组合桨等比例缩小建立模型,基于计算流体力学(CFD)中的多重参考系法对该双层组合桨搅拌釜流场进行了模拟研究,并利用粒子图像测速(PIV)实验对模拟结果进行了验证。分析了桨叶离底间距、桨间距及组合桨安装角度的变化对流场产生的影响。随着离底间距的增大,搅拌釜下层框式桨横梁处产生往槽底的轴向流强度会逐渐减弱,不利于底部物料的混合;桨间距的增加导致两桨间对流减弱,不利于两桨间流体的混合,当桨间距与釜内径的比值为0.77时,搅拌釜内的整体流动情况较好。对上下层桨叶安装角度分别为0°、45°和90°这3种工况下的釜内流场特性研究表明,安装角度为90°时,斜叶桨产生的轴向流强度最大,此时搅拌釜内流体的混合效果最好。研究结果为改进型框式桨与二斜叶桨双层组合桨应用于树脂聚合反应实际工程提供参考。

关键词: 改进型框式组合桨, 混合, 粒子图像测速, 计算流体力学

Abstract:

The 5m3 resin reactor equipped with an improved frame type-two oblique double layer combined impellers was scaled down,and its calculation model was established. The flow field in the mentioned stirred tank was numerically investigated by using multi-reference frame method based on the computational fluid dynamics (CFD) simulation code Fluent, and the simulation results were validated by PIV experiments. The effects on the flow field arising from the installation height of impellers (C1), the distance between two impellers (C2) as well as the installation angle of combined impeller (β) were investigated. With the increase of C1, the axial flow from the beam of frame impeller to the bottom of the stirred tank will gradually decrease, which is not conducive to the mixing of the materials in the bottom of the tank. The increase of C2 leads to the weakening of convection between the two propellers, which is not conducive to the mixing of fluid between the two propellers. When the ratio of propeller spacing to vessel diameter is 0.77, the overall flow in the stirred tank is better. The flow field characteristics of the blade installation angles of 0°, 45°and 90°show that the axial flow intensity produced by the inclined blade is the largest when β is 90°, and the mixing effect of the fluid in the stirred tank is the best. The results provide a reference for the application of the improved frame type-two oblique double layer combined impeller in the practical engineering of resin polymerization reaction.

Key words: improved frame type combined impeller, mixing, particle image velocimetry (PIV), computational fluid dynamics(CFD)

中图分类号: 

版权所有 © 《化工进展》编辑部


本系统由北京玛格泰克科技发展有限公司设计开发 技术支持:support@magtech.com.cn