燃料电池用柴油重整制氢技术现状与展望

doi:10.16085/j.issn.1000-6613.2020-0539

摘要/Abstract

摘要：

现有储氢技术在储氢密度、能耗及相应的基础设施建设等方面存在明显短板，难以满足燃料电池技术商业化发展需求，现场制氢技术得到了广泛关注。其中，柴油重整制氢技术以其理论产氢比率高、适用领域广、基础设施完善、安全性好、成本低等优点，可广泛应用于汽车、船舶、分布式发电等民用领域以及潜艇、舰船等军事领域，成为热点研究之一。本文综述了柴油重整制氢的分类，详细介绍了蒸汽重整、部分氧化重整和自热重整制氢的反应机理，并对三种重整反应的优缺点进行了对比分析；在此基础上，概述了三种重整反应国内外研究现状。总体而言，蒸汽重整产物中氢气浓度最高但系统质量较大，比较适用于固定制氢领域；自热重整技术系统结构较为紧凑，产物氢气浓度适中，比较适用于汽车等移动制氢领域；部分氧化重整技术由于产物H₂/CO比率较低，加之反应温度较高，容易发生结焦反应，目前其应用领域还相对有限。

关键词: 柴油重整, 制氢, 燃料电池

Abstract:

Due to the obvious defects in hydrogen storage density, energy consumption and the relative infrastructure construction, the existing hydrogen storage technology is difficult to meet the commercial needs of fuel cell technology. The on site hydrogen production technology has attracted the abroad attentions，with the advantages of high hydrogen production rate, wide application field, perfect infrastructure, good safety and low cost, the hydrogen production technology of diesel reforming can be widely applied in automobile, ship, distributed power generation and other civil fields as well as submarine, warship and other military fields, thus has become one of hot-spots worth studying. In this paper, the diesel reforming for hydrogen production technologies are introduced and classified, the reaction mechanisms of steam reforming, partial oxidation and autothermal reforming are specified, and a comparative analysis of the positive and negative aspects of the three diesel reforming technology are carried out. On this basis, the research progress of the three diesel reforming technology are summarized. Overall, the steam reforming technology has the highest hydrogen concentration and higher system weight, which is more suitable for fixed hydrogen production. Due to the compact structure and the moderate hydrogen concentration of the product, the autothermal reforming technology is considered more suitable for automobile and other mobile hydrogen production field. By comparison, because of lower H₂/CO ratio of the product, higher reaction temperature which prone to coking reaction, the applications of partial oxidation technology are relatively limited.

Key words: diesel reforming, hydrogen production, fuel cell

中图分类号:

TQ116.2

袁斌, 潘建欣, 王傲, 彭元亭. 燃料电池用柴油重整制氢技术现状与展望[J]. 化工进展, 2020, 39(S1): 107-115.

Bin YUAN, Jianxin PAN, Ao WANG, Yuanting PENG. Research progress and perspective of diesel reforming to hydrogen production for fuel cell applications[J]. Chemical Industry and Engineering Progress, 2020, 39(S1): 107-115.

图/表 4

参考文献 40

1	衣宝廉. 燃料电池——原理·技术·应用[M]. 北京: 化学工业出版社, 2003.
	YI Baolian. Fuel cell—principle, technology and application[M]. Beijing: Chemical Industry Press, 2003.
2	谢欣烁, 杨卫娟, 施伟, 等. 制氢技术的生命周期评价研究进展[J]. 化工进展, 2018, 37(6): 2147-2158.
	XIE Xinshuo, YANG Weijuan, SHI Wei, et al. Life cycle assessment of technologies for hydrogen production-a review[J]. Chemical Industry and Engineering Progress, 2018, 37(6): 2147-2158.
3	黄格省, 李锦山, 魏寿祥, 等. 化石原料制氢技术发展现状与经济性分析[J]. 化工进展, 2019, 38(12): 5217-5224.
	HUANG Gesheng, LI Jinshan, WEI Shouxiang,et al. Status and economic analysis of hydrogen production technology from fossil raw materials[J]. Chemical Industry and Engineering Progress, 2019, 38(12): 5217-5224.
4	PEREIRA C, J-M BAE, AHMED S, et al. Liquid fuel reformer development: autothermal reforming of diesel fuel[R]. U.S Department of Energy, 2000.
5	GLOCKLIN K. Economic analysis of various reforming techniques and fuel sources for hydrogen producton[D]. Auburn: Auburn University, 2006.
6	PARMAR R D, KUNDU A, KARAN K. Thermodynamic analysis of diesel reforming process: mapping of carbon formation boundary and representative independent reactions[J]. Journal Power Sources, 2009, 194: 1007-1020.
7	MARTIN S, KRAAIJ G, ASCHER T, et al. Direct steam reforming of diesel and diesele-biodiesel blends for distributed hydrogen generation[J]. International Journal of Hydrogen Energy, 2015, 40: 75-84.
8	YERGA R M, ALVAREZ-GALVAN M C, MOTA N, et al. Catalysts for hydrogen production from heavy hydrocarbons[J]. Chem. Cat. Chem., 2011, 3: 440-457.
9	THORMANN J, MAIEAR L, PFEIFER P, et al. Steam reforming of hexadecane over a Rh/CeO₂ catalyst in microchannels: experimental and numerical investigation[J]. International Journal of Hydrogen Energy, 2009, 34: 5108-5120.
10	STEINBERG M. Hydrogen production from fossil fuels, energy carrier and conversion systems[EL/OL].
11	MA L, TRIMM D L, JIANG C. The design and testing of an autothermal reactor for the conversion of light hydrogarbons to hydrogen I: The kinetics of the catalytic oxidation of light hydrocarbons[J]. Appl. Catal. A, 1996, 128: 275-283.
12	CUTILLO A, ANTONINI M, SPECCHIA S, et al. Performance comparison between autothermal and steam reforming in a diesel fuel processor for a pem fuel cell[C]//Joint Meeting of the Greek and Italian Sections of The Combustion Institute, 2009: 105-118.
13	HAN F, KAHALICH M, BEHM R J, et al. Kinetic study of selective CO oxidation in H₂-rich gas on a Ru/Y-Al₂O₃ catalyst[J]. Phys. Chem. Chem. Phys., 2002, 2: 389-384.
14	MIEVILLE R L. Coking characteristics of reforming catalysts[J]. J. Catal., 1986, 100: 482-488.
15	KANG I, BAE J, YOON S, et al. Performance improvement of diesel autothermal reformer by applying ultrasonic injector for effective fuel delivery[J]. Power Sources, 2007,172: 845-852.
16	BORUP R L, INBODY M A. Fuel composition effects on transportation fuel cell reforming[J]. Catal. Today, 2005, 99: 263-270.
17	KARATZAS X, NILSSON M, DAWODY J, et al. Characterization and optimization of an autothermal diesel and jet fuel reformer for 5 kWe mobile fuel cell applications[J]. Chemical Engineering Journal, 2010,156: 366-379.
18	HOLLADAY J, HU J, KING D L, et al. An overview of hydrogen production technologies[J]. Catal. Today, 2009, 139: 244-260.
19	WILHELM D J, SIMBECK D R, KARP A D, et al. Syngas production for gas-to-liquids applications: technologies, issues and outlook[J]. Fuel Process Technol., 2001, 71: 139-148.
20	HUERTA G V, JORDAN G A, DRAGON M, et al. Exergy analysis of the diesel pre-reforming solid oxide fuel cell system with anode off-gas recycling in the SchIBZ project. Part I: Modeling and validation[J]. International Journal of Hydrogen Energy, 2018, 43: 16684-16693.
21	NAVARRO R M, PENA M A, FIERRO J. Hydrogen production reactions from carbon feedstocks: fossil fuels and biomass[J]. Chem. Rev., 2007,107: 3952-3991.
22	MING Q, HEALEY T, ALLEN L, et al. Steam reforming of hydrocarbon fuels[J]. Catal. Today, 2002,77: 51-64.
23	THORMANN J, PFEIFER P, SCHUBERT K, et.al. Reforming of diesel fuel in a micro reactor for APU systems[J]. Chemical Engineering Journal, 2008, 135: S74–S81.
24	MARTIN S, KRAAIJ G, ASCHER T, et al. Direct steam reforming of diesel and dieselebiodiesel blends for distributed hydrogen generation[J]. International Journal of Hydrogen Energy, 2015, 40: 75-84.
25	BOZDAG A A, KAYNAR A D D, DOGU T, et al. Development of ceria and tungsten promoted nickel/alumina catalysts for steam reforming of diesel[J]. Chemical Engineering Journal, 2019, 377: 120274.
26	BOON J, DIJK E VAN, DE MUNCK S, et al. Steam reforming of commercial ultra-low sulphur diesel[J]. Journal of Power Sources, 2011, 196: 5928-5935.
27	徐立昊, 米万良, 苏庆泉. 入口气组分对质子交换膜燃料电池柴油水蒸气重整制氢流程的影响[J]. 北京科技大学学报, 2012(6): 712-717.
	XU Lihao, MI Wanliang, SU Qingquan. Influence of inlet gas components on the diesel steam reforming of proton exchange membrane fuel cells for hydrogen production[J]. Journal of University of Science and Technology Beijing, 2012(6): 712-717.
28	BROWN L F. A survey of processes for producing hydrogen fuel from different sources for aotumotive-propulsion fuel cells[R]. Los Alamos Nafional Laboratory, 1996.
29	AHMED S. Catalytic partial oxidation reforming of hydrocarbon fuels[C]//Fuel Cell Seminar Palm Springs, CA,1998.
30	ELGHAWIA U, THEINNOI K, SITSHEBO S, et al. GC-MS determination of low hydrocarbon species (C₁-C₆) from a diesel partial oxidation reformer[J]. International Journal of Hydrogen Energy, 2008, 33: 7074-7083.
31	KRUMMENACHER J, WEST K, SCHMIDT L. Catalytic partial oxidation of higher hydrocarbons at millisecond contact times: decane, hexadecane, and diesel fuel[J]. Journal of Catalysis, 2003, 215:332-343.
32	周琦, 郭瓦力, 任洪宝, 等. 柴油部分氧化重整制氢[J]. 天然气化工, 2009(3)34-37.
	ZHOU Qi, GUO Wali, REN Hongbao, et al. Partial oxidation reforming of diesel for hydrogen production[J]. Natural Gas Chemical Industry,2009(3): 34-37.
33	于涛, 郭瓦力, 丁东各, 等.柴油自热重整制氢反应及反应器[J].现代化工, 2010, 30(3): 73-78.
	YU Tao, GUO Wali, Dongge DIN, et al. Reaction and reactor of autothermal reforming for hydrogen production with diesel[J].Modern Chemical Industry, 2010, 30(3): 73-78.
34	于涛, 郭瓦力, 王建武, 等. 柴油自热重整制氢工艺过程研究[J]. 天然气化工, 2010, 35(1): 46-49.
	YU Tao, GUO Wali, WANG Jianwu, et al. Study on process of autothermal reforming of diesel to hydrogen[J]. Natural Gas Chemical Industry, 2010, 35(1): 46-49.
35	于涛, 郭瓦力, 李芳芳, 等. PtLaCe/Al₂O₃催化柴油自热重整制氢的研究[J]. 可再生能源, 2009, 27(6): 41-49.
	YU Tao, GUO Wali, LI Fangfang, et al. PtLaCe/Al₂O₃ catalyst used autothermally reforming of diesel for hydrogen product[J]. Renewable Energy Resources, 2009, 27(6): 41-49.
36	KRUMPELT M, KRAUSE T, KOPASZ J P, et al. Catalytic autothermal reforming of hydrocarbon fuels for fuel cells[C]//American Institute of Chemical Engineering Spring National Meeting, CA, 2002.
37	KANG I, BAE J. Autothermal reforming study of diesel for fuel cell application[J]. Journal of Power Sources, 2006,159(2):1283-1290.
38	GONZÁLEZ A V, PETTERSSON L J. Full-scale autothermal reforming for transport applications: the effect of diesel fuel quality[J]. Catalysis Today, 2013,210:19-25.
39	O’CONNELL M, KOLB G, SCHELHAAS K P, et al. Development and evaluation of a microreactor for thereforming of diesel fuel in the kW range[J]. International Journal of Hydrogen Energy, 2009, 34: 6290-6303.
40	SAMSUN R C, PRAWITZ M, TSCHAUDER A, et al. An autothermal reforming system for diesel and jet fuel with quick start-up capability[J]. International Journal of Hydrogen Energy, 2019, 44(51): 27749-27764.

[1]	陈匡胤, 李蕊兰, 童杨, 沈建华. 质子交换膜燃料电池气体扩散层结构与设计研究进展[J]. 化工进展, 2023, 42(S1): 246-259.
[2]	谢璐垚, 陈崧哲, 王来军, 张平. 用于SO₂去极化电解制氢的铂基催化剂[J]. 化工进展, 2023, 42(S1): 299-309.
[3]	许家珩, 李永胜, 罗春欢, 苏庆泉. 甲醇水蒸气重整工艺的优化[J]. 化工进展, 2023, 42(S1): 41-46.
[4]	张启, 赵红, 荣峻峰. 质子交换膜燃料电池中氧还原反应抗毒性电催化剂研究进展[J]. 化工进展, 2023, 42(9): 4677-4691.
[5]	张亚娟, 徐惠, 胡贝, 史星伟. 化学镀法制备NiCoP/rGO/NF高效电解水析氢催化剂[J]. 化工进展, 2023, 42(8): 4275-4282.
[6]	王蕴青, 杨国锐, 延卫. 过渡金属磷化物的改性方法及其在电化学析氢中的应用[J]. 化工进展, 2023, 42(7): 3532-3549.
[7]	蒋博龙, 崔艳艳, 史顺杰, 常嘉城, 姜楠, 谭伟强. 过渡金属Co₃O₄/ZnO-ZIF氧还原催化剂Co/Zn-ZIF模板法制备及其产电性能[J]. 化工进展, 2023, 42(6): 3066-3076.
[8]	马哲杰, 张文励, 赵炫凯, 李平. PEMFC阴极催化层氧传质阻力影响的研究进展[J]. 化工进展, 2023, 42(6): 2860-2873.
[9]	符淑瑢, 王丽娜, 王东伟, 刘蕊, 张晓慧, 马占伟. 析氧助催化剂增强光阳极光电催化分解水性能研究进展[J]. 化工进展, 2023, 42(5): 2353-2370.
[10]	于海强, 郭泉忠, 杜克勤, 汪川. 脉冲电沉积PbO₂涂层在PEMFC不锈钢双极板上的应用[J]. 化工进展, 2023, 42(2): 917-924.
[11]	高帷韬, 殷屺男, 涂自强, 龚繁, 李阳, 徐宏, 王诚, 毛宗强. 金属有机框架材料中的质子传导及其在质子交换膜中的应用[J]. 化工进展, 2022, 41(S1): 260-268.
[12]	肖周荣, 李国柱, 王涖, 张香文, 谷建民, 王德松. 液体碳氢燃料蒸汽重整制氢催化剂研究进展[J]. 化工进展, 2022, 41(S1): 97-107.
[13]	胡兵, 徐立军, 何山, 苏昕, 汪继伟. 碳达峰与碳中和目标下PEM电解水制氢研究进展[J]. 化工进展, 2022, 41(9): 4595-4604.
[14]	闫鹏, 程易. 用于分布式制氢的甲烷蒸汽重整膜反应器的数值模拟[J]. 化工进展, 2022, 41(7): 3446-3454.
[15]	陈哲坤, 潘伟童, 姚顶松, 丁路, 王辅臣. 质子交换膜燃料电池微孔层浆液微观结构与流变性[J]. 化工进展, 2022, 41(7): 3808-3815.