考虑管壳式换热器传热强化的换热网络综合研究进展

doi:10.16085/j.issn.1000-6613.2017-2614

化工进展 ›› 2018, Vol. 37 ›› Issue (04): 1267-1275.DOI: 10.16085/j.issn.1000-6613.2017-2614

考虑管壳式换热器传热强化的换热网络综合研究进展

肖武¹, 史朝霞¹, 姜晓滨¹, 李祥村¹, 吴雪梅¹, 贺高红¹, 罗立²

1 大连理工大学精细化工国家重点实验室, 膜科学与技术研究开发中心, 辽宁大连 116024;
2 北京沃利帕森工程技术有限公司, 北京 100015

收稿日期:2017-12-18 修回日期:2018-01-08 出版日期:2018-04-05 发布日期:2018-04-05
通讯作者: 贺高红,博士,教授,主要从事膜分离过程、环保和过程工业节能改造等方面研究。
作者简介:肖武(1977-),男,博士,副教授,从事化学工程、化工系统工程及过程强化等方面研究。E-mail:wuxiao@dlut.edu.cn。
基金资助:
国家自然科学基金（21676043）、长江学者奖励计划（T2012049）、中央高校基本科研业务费专项基金（DUT17JC33，DUT17ZD203，DUT16TD19）及辽宁省高等学校创新团队项目（LT2015007）。

Research progress on heat exchanger network considering heat transfer enhancement of shell-and-tube exchangers

XIAO Wu¹, SHI Zhaoxia¹, JIANG Xiaobin¹, LI Xiangcun¹, WU Xuemei¹, HE Gaohong¹, LUO Li²

1 State Key Laboratory of Fine Chemicals, R & D Center of Membrane Science and Technology, Dalian University of Technology, Dalian 116024, Liaoning, China;
2 Beijing Worley Parsons Engineering Technology Co., Ltd., Beijing 100015, China

Received:2017-12-18 Revised:2018-01-08 Online:2018-04-05 Published:2018-04-05

摘要/Abstract

摘要： 换热器传热强化在换热网络中的应用可以解决现有换热网络改造中的瓶颈问题，在热回收系统配置没有过多结构改造的条件下，可以达到明显的节能及降低成本的目的；同时，在换热网络设计中，换热器传热强化技术的应用可以降低设备投资，实现更好的经济效果。本文首先通过文献检索数据说明了在换热网络改造和设计中考虑传热强化技术的研究在近5年得到了研究者的关注。然后概述了管壳式换热器传热强化的基本原理及主要方式，分析了传热强化技术的应用对换热器传热性能的影响，系统总结了管壳式换热器传热强化技术的分类和强化效果。进一步从设计和改造两个方面，对换热网络优化中考虑管壳式换热器传热强化的应用研究进行了综述，展示了传热强化对换热网络设计和改造的效果和优势。最后对下一步的研究进行了展望，指出可进一步探究换热器传热强化设备几何尺寸和换热网络同步优化、传热强化和换热器详细设计同步优化等。

关键词: 传热强化, 管壳式换热器, 换热网络, 设计, 改造

Abstract: The implementation of enhanced heat transfer technology in heat exchangers can solve the bottleneck problem in the existing heat exchanger network(HEN) retrofit. Without excessive structural transformation in the heat recovery system,the use of heat transfer enhancement technology can achieve significant energy savings and reduce costs. At the same time,in the design of HEN,the application of heat transfer enhancement technology in heat exchangers can reduce the investment of equipment and achieve better economic effect. Firstly,through the literature retrieval data,the research on heat transfer enhancement in heat transfer network retrofit and design has been paid attention by researchers in the last 5 years. Then,the basic principles and main methods of heat transfer enhancement of shell and tube heat exchangers(STHE) were summarized. The effect of heat transfer enhancement technology on heat transfer performance of heat exchanger was analyzed. The classification of heat transfer enhancement technology and the enhancement effect of STHE were summarized. From the two aspects of design and retrofit,the application research of heat transfer enhancement of STHE considering in the optimization of HEN was summarized. The effect and advantage of heat transfer enhancement on HEN design and retrofit were presented. Finally,the future research,the simultaneous optimization of heat transfer enhancement device geometry of STHE and HEN,as well as simultaneous optimization of heat transfer enhancement and detailed design of heat exchanger was prospected.

Key words: heat transfer enhancement, shell-and-tube heat exchanger, heat exchanger networks, design, retrofit

中图分类号:

TQ021.8

肖武, 史朝霞, 姜晓滨, 李祥村, 吴雪梅, 贺高红, 罗立. 考虑管壳式换热器传热强化的换热网络综合研究进展[J]. 化工进展, 2018, 37(04): 1267-1275.

XIAO Wu, SHI Zhaoxia, JIANG Xiaobin, LI Xiangcun, WU Xuemei, HE Gaohong, LUO Li. Research progress on heat exchanger network considering heat transfer enhancement of shell-and-tube exchangers[J]. Chemical Industry and Engineering Progress, 2018, 37(04): 1267-1275.

参考文献

[1] ABUHALIMA O,张隽,孙琳,等. 换热网络综合中管壳式换热器设计研究进展[J]. 计算机与应用化学,2015,32(1):9-14. ABUHALIMA O,ZHANG J,SUN L,et al. Research progress in the design of shell and tube heat exchangers in the synthesis of heat exchanger networks[J]. Computers and Applied Chemistry,2015,32(1):9-14.
[2] PAN M,BULATOV I,SMITH R. Recent methods for retrofitting heat exchanger networks with heat transfer intensifications[J]. Chemical Engineering Transactions,2014,39:1435-1440.
[3] 曹振恒,赵立功,王彩琴,等. 管壳式换热器壳程传热强化研究进展[J]. 化学工程与装备,2015(3):174-176. CAO Z H,ZHAO L G,WANG C Q,et al. Research progress on heat transfer enhancement of shell side in shell and tube heat exchanger[J]. Chemical Engineering & Equipment,2015(3):174-176.
[4] POLLEY G T,ATHIE C M R,GOUGH M. Use of heat transfer enhancement in process integration[J]. Heat Recovery Systems & Chp,1992,12(3):191-202.
[5] LIU Z Y,VARBANOV P S,KLEMES J J,et al. Recent developments in applied thermal engineering:process integration,heat exchangers,enhanced heat transfer,solar thermal energy,combustion and high temperature processes and thermal process modelling[J]. Applied Thermal Engineering,2016,105:755-762.
[6] 王丽丽,马贵阳. 纵流式换热器结构优化研究进展[J]. 当代化工,2016,45(8):1937-1939. WANG L L,MA G Y. Research process of structural optimization of heat exchangers with longitudinal flow[J]. Contemporary Chemical Industry,2016,45(8):1937-1939.
[7] 王琰,杨建锋,曾敏,等. 一种新型连续螺旋折流板管壳式汽车空调回热器[J]. 化工学报,2014,65(s1):264-271. WANG Y,YANG J F,ZENG M,et al. A new type of liquid-suction heat exchanger for automotive air conditioning system[J]. CIESC Journal,2014,65(s1):264-271.
[8] PAN M,BULATOV I,SMITH R. Efficient retrofitting approach for improving heat recovery in heat exchanger networks with heat transfer intensification[J]. Industrial & Engineering Chemistry Research,2014,53(27):11107-11120.
[9] SHEIKHOLESLAMI M,GORJI-BANDPY M,GANJI D D. Review of heat transfer enhancement methods:focus on passive methods using swirl flow devices[J]. Renewable & Sustainable Energy Reviews,2015,49:444-469.
[10] 赵晓曦,邓先和,陈颖,等. 管壳式换热器壳程传热强化研究[J]. 现代化工,2001,21(7):14-17. ZHAO X X,DENG X H,CHEN Y,et al. Heat transfer enhancement in shellside of shell and tube heat exchanger[J]. Modern Chemical Industry,2001,21(7):14-17.
[11] HAMEED V M,HUSSEIN M A. Effect of new type of enhancement on inside and outside surface of the tube side in single pass heat exchanger[J]. Applied Thermal Engineering,2017,122:484-491.
[12] 刘敏珊,宫本希,董其伍. 螺旋扁管的换热性能研究[J]. 石油机械,2008,36(2):22-25. LIU M S,GONG B X,DONG Q W. Study on the heat transfer performance of a spiral flat tube[J]. China Petroleum Machinery,2008,36(2):22-25.
[13] 王丹,董其伍,刘敏珊. 低Re数下正弦波纹流道内流体混合性能研究[J]. 机械设计与制造,2012(6):186-188. WANG D,DONG Q W,LIU M S. Research on the mixing performance of fluid flow in sinusoidal corrugated channel at low Reynolds number[J]. Machinery Design & Manufacture,2012(6):186-188.
[14] 丁聪,高学农. 高黏度流体的传热强化研究进展[J]. 化工进展,2012,31(s1):416-419. DING C,GAO X N. Research development of high viscosity fluid in heat transfer enhancement[J]. Chemical Industry and Engineering Progress,2012,31(s1):416-419.
[15] 李若兰,丁杰,霍正齐. 管壳式换热器换热管的传热强化[J]. 制冷,2013(3):76-81. LI R L,DING J,HUO Z Q. Heat transfer enhancement of shell and tube heat exchanger heat transfer tube[J]. Refrigeration,2013(3):76-81.
[16] BILEN K,CETIN M,GUL H,et al. The investigation of groove geometry effect on heat transfer for internally grooved tubes[J]. Applied Thermal Engineering,2009,29(4):753-761.
[17] MOHAMMED H A,ABBAS A K,SHERIFF J M. Influence of geometrical parameters and forced convective heat transfer in transversely corrugated circular tubes[J]. International Communications in Heat & Mass Transfer,2013,44(5):116-126.
[18] WANG L,SUNDEN B. Performance comparison of some tube inserts[J]. International Communications in Heat & Mass Transfer,2002,29(1):45-56.
[19] GARCIA A,VICENTE P G,VIEDMA A. Experimental study of heat transfer enhancement with wire coil inserts in laminar-transition-turbulent regimes at different Prandtl numbers[J]. International Journal of Heat & Mass Transfer,2005,48(21/22):4640-4651.
[20] ZDANIUK G J,CHAMRA L M,MAGO P J. Experimental determination of heat transfer and friction in helically-finned tubes[J]. Experimental Thermal & Fluid Science,2008,32(3):761-775.
[21] WANG C C,LEE W S,SHEU W J. A comparative study of compact enhanced fin-and-tube heat exchangers[J]. International Journal of Heat & Mass Transfer,2001,44(18):3565-3573.
[22] LIM K Y,HUNG Y M,TAN B T. Performance evaluation of twisted-tape insert induced swirl flow in a laminar thermally developing heat exchanger[J]. Applied Thermal Engineering,2017,121:652-661.
[23] KEKLIKCIOGLU O,OZCEYHAN V. Experimental investigation on heat transfer enhancement of a tube with coiled-wire inserts installed with a separation from the tube wall[J]. International Communications in Heat & Mass Transfer,2016,78:88-94.
[24] SAN J Y,HUANG W C,CHEN C A. Experimental investigation on heat transfer and fluid friction correlations for circular tubes with coiled-wire inserts[J]. International Communications in Heat & Mass Transfer,2015,65:8-14.
[25] YUN J Y,LEE K S. Influence of design parameters on the heat transfer and flow friction characteristics of the heat exchanger with slit fins[J]. International Journal of Heat & Mass Transfer,2000,43(14):2529-2539.
[26] SAHA S K,DUTTA A,DHAL S K. Friction and heat transfer characteristics of laminar swirl flow through a circular tube fitted with regularly spaced twisted-tape elements[J]. International Journal of Heat & Mass Transfer,2001,44(22):4211-4223.
[27] HONG Y,DU J,WANG S. Experimental heat transfer and flow characteristics in a spiral grooved tube with overlapped large/small twin twisted tapes[J]. International Journal of Heat & Mass Transfer,2016,106:1178-1190.
[28] NOZU S,HONDA H. Condensation of refrigerants in horizontal,spirally grooved microfin tubes:numerical analysis of heat transfer in the annular flow regime[J]. Journal of Heat Transfer,2000,122(1):80-91.
[29] AL-FAHED S,CHAMRA L,CHAKROUN W. Pressure drop and heat transfer comparison for both microfin tube and twisted-tape inserts in laminar flow[J]. Experimental Thermal and Fluid Science,1998,18(4):323-333.
[30] 朱冬生,肖建国. 轧槽管抗污垢性能的试验研究[J]. 石油化工设备,1996(1):8-11. ZHU D S,XIAO J G. Study on anti-fouling characteristics of the corrugated tube[J]. PetroChemical Equipment,1996(1):8-11.
[31] ROZZI S,MASSINI R,PACIELLO G,et al.Heat treatment of fluid foods in a shell and tube heat exchanger:comparison between smooth and helically corrugated wall tubes[J]. Journal of Food Engineering,2007,79(1):249-254.
[32] LI H,KOTTKE V. Effect of the leakage on pressure drop and local heat transfer in shell-and-tube heat exchangers for staggered tube arrangement[J]. International Journal of Heat & Mass Transfer,1998,41(2):425-433.
[33] 王英双,刘志春,黄素逸,等. 新型折流杆换热器的流动与传热数值模拟[J]. 化工进展,2010,29(7):1205-1208. WANG Y S,LIU Z C,HUANG S Y,et al. Fluid flow and heat transfer in rod baffle heat exchanger shell side[J]. Chemical Industry and Engineering Progress,2010,29(7):1205-1208.
[34] 古新,秦晓柯,王永庆,等. 倾斜折流栅式换热器壳程流体流动与传热特性[J]. 化工进展,2017,36(10):3584-3589. GU X,QIN X K,WANG Y Q,et al. Research on fluid flow and heat transfer characteristics in shell side of inclined shutter baffle heat exchanger[J]. Chemical Industry and Engineering Progress,2017,36(10):3584-3589.
[35] ZHOU G Y,XIAO J,ZHU L,et al. A numerical study on the shell-side turbulent heat transfer enhancement of shell-and-tube heat exchanger with trefoil-hole baffles[J]. Energy Procedia,2015,75:3174-3179.
[36] WANG Q,CHEN G,CHEN Q,et al. Review of improvements on shell-and-tube heat exchangers with helical baffles[J]. Heat Transfer Engineering,2010,31(10):836-853.
[37] WEN J,YANG H,JIAN G,et al. Energy and cost optimization of shell and tube heat exchanger with helical baffles using Kriging metamodel based on MOGA[J]. International Journal of Heat & Mass Transfer,2016,98:29-39.
[38] 文键,杨辉,王斯民,等. 旋梯式螺旋折流板换热器优化结构的数值模拟[J]. 西安交通大学学报,2014,48(11):8-14. WEN J,YANG H,WANG S M,et al. Numerical simulation for configuration optimization of heat exchanger with helical baffles[J]. Journal of Xi'an Jiaotong University,2014,48(11):8-14.
[39] 王斯民,肖娟,王家瑞,等. 折面螺旋折流板换热器的流动传热性能实验研究[J]. 化工学报,2017,68(12):4537-4544. WANG S M,XIAO J,WANG J R,et al. Flow and heat transfer performance of shell-and-tube heat exchangers with fold helical baffles[J]. CIESC Journal,2017,68(12):4537-4544.
[40] WEN J,YANG H,WANG S,et al. PIV experimental investigation on shell-side flow patterns of shell and tube heat exchanger with different helical baffles[J]. International Journal of Heat & Mass Transfer,2017,104:247-259.
[41] ZHANG J F,LI B,HUANG W J,et al. Experimental performance comparison of shell-side heat transfer for shell-and-tube heat exchangers with middle-overlapped helical baffles and segmental baffles[J]. Chemical Engineering Science,2009,64(8):1643-1653.
[42] LIU L,FAN Y,LING X,et al. Flow and heat transfer characteristics of finned tube with internal and external fins in air cooler for waste heat recovery of gas-fired boiler system[J]. Chemical Engineering & Processing Process Intensification,2013,74(8):142-152.
[43] BIYANTO T R,GONAWAN E K,NUGROHO G,et al. Heat exchanger network retrofit throughout overall heat transfer coefficient by using genetic algorithm[J]. Applied Thermal Engineering,2016,94:274-281.
[44] ZHU X X,ZANFIR M,KLEMES J. Heat transfer enhancement for heat exchanger network retrofit[J]. Heat Transfer Engineering,2000,21(2):7-18.
[45] PAN M,BULATOV I,SMITH R,et al. Novel MILP-based iterative method for the retrofit of heat exchanger networks with intensified heat transfer[J]. Computers & Chemical Engineering,2012,42(27):263-276.
[46] WANG Y,PAN M,BULATOV I,et al. Application of intensified heat transfer for the retrofit of heat exchanger network[J]. Applied Energy,2012,89(1):45-59.
[47] AKPOMIEMIE M O,SMITH R. Retrofit of heat exchanger networks without topology modifications and additional heat transfer area[J]. Applied Energy,2015,159:381-390.
[48] PAN M,BULATOV I,SMITH R. Exploiting tube inserts to intensify heat transfer for the retrofit of heat exchanger networks considering fouling mitigation[J]. Industrial & Engineering Chemistry Research,2013,52(8):2925-2943.
[49] JIANG N,SHELLEY J D,SMITH R. New models for conventional and heat exchangers enhanced with tube inserts for heat exchanger network retrofit[J]. Applied Thermal Engineering,2014,70(1):944-956.
[50] PAN M,BULATOV I,SMITH R. Improving heat recovery in retrofitting heat exchanger networks with heat transfer intensification,pressure drop constraint and fouling mitigation[J]. Applied Energy,2016,161:611-626.
[51] AKPOMIEMIE M O,SMITH R. Pressure drop considerations with heat transfer enhancement in heat exchanger network retrofit[J]. Applied Thermal Engineering,2017,116:695-708.
[52] 尹清华,华贲,吴国东,等.同时考虑流动(火用)损费和传热强化的换热网络合成[J]. 化工学报,1992,43(1):54-61. YIN Q H,HUA B,WU G D,et al. Considering the flow of energy loss cost together with heat transfer enhancement of heat exchanger network synthesis[J]. CIESC Journal,1992,43(1):54-61.
[53] ODEJOBI O J,ADEJIKUN A E,AL-MUTAIRI E M. Heat exchanger network synthesis incorporating enhanced heat transfer techniques[J]. Applied Thermal Engineering,2015,89:684-692.

考虑管壳式换热器传热强化的换热网络综合研究进展

Research progress on heat exchanger network considering heat transfer enhancement of shell-and-tube exchangers

PDF (PC)

可视化

被引次数

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	徐晨阳, 都健, 张磊. 基于图神经网络的化学反应优劣评价[J]. 化工进展, 2023, 42(S1): 205-212.
[2]	陈匡胤, 李蕊兰, 童杨, 沈建华. 质子交换膜燃料电池气体扩散层结构与设计研究进展[J]. 化工进展, 2023, 42(S1): 246-259.
[3]	孙玉玉, 蔡鑫磊, 汤吉海, 黄晶晶, 黄益平, 刘杰. 反应精馏合成甲基丙烯酸甲酯工艺优化及节能[J]. 化工进展, 2023, 42(S1): 56-63.
[4]	刘炫麟, 王驿凯, 戴苏洲, 殷勇高. 热泵中氨基甲酸铵分解反应特性及反应器结构优化[J]. 化工进展, 2023, 42(9): 4522-4530.
[5]	王晨, 白浩良, 康雪. 大功率UV-LED散热与纳米TiO₂光催化酸性红26耦合系统性能[J]. 化工进展, 2023, 42(9): 4905-4916.
[6]	吴正浩, 周天航, 蓝兴英, 徐春明. 人工智能驱动化学品创新设计的实践与展望[J]. 化工进展, 2023, 42(8): 3910-3916.
[7]	杨志强, 曾纪珺, 马义丁, 尉涛, 赵波, 刘英哲, 张伟, 吕剑, 李兴文, 张博雅, 唐念, 李丽, 孙东伟. 六氟化硫替代气体的研究现状及未来发展趋势[J]. 化工进展, 2023, 42(8): 4093-4107.
[8]	郭晋, 张耕, 陈国华, 朱鸣, 谭粤, 李蔚, 夏莉, 胡昆. 车载液氢气瓶设计技术的研究进展[J]. 化工进展, 2023, 42(8): 4221-4229.
[9]	薛凯, 王帅, 马金鹏, 胡晓阳, 种道彤, 王进仕, 严俊杰. 工业园区分布式综合能源系统的规划与调度[J]. 化工进展, 2023, 42(7): 3510-3519.
[10]	周龙大, 赵立新, 徐保蕊, 张爽, 刘琳. 电场-旋流耦合强化多相介质分离研究进展[J]. 化工进展, 2023, 42(7): 3443-3456.
[11]	李蓝宇, 黄新烨, 王笑楠, 邱彤. 化工科研范式智能化转型的思考与展望[J]. 化工进展, 2023, 42(7): 3325-3330.
[12]	顾诗亚, 董亚超, 刘琳琳, 张磊, 庄钰, 都健. 考虑中间节点的碳捕集管路系统设计与优化[J]. 化工进展, 2023, 42(6): 2799-2808.
[13]	李雪, 王艳君, 王玉超, 陶胜洋. 仿生表面用于雾水收集的最新研究进展[J]. 化工进展, 2023, 42(5): 2486-2503.
[14]	王子杰, 陆树银, 赵梓良, 王宁, 顾煜炯. 供热改造对火电机组性能的影响分析[J]. 化工进展, 2023, 42(5): 2325-2331.
[15]	邹银才, 李清国, 吴辉, 钟小兵, 陈咸志. 弹载相变热沉传热仿真与优化[J]. 化工进展, 2023, 42(3): 1248-1256.