连通微通道内过冷流动沸腾传热强化机理分析

doi:10.16085/j.issn.1000-6613.2021-1538

摘要/Abstract

摘要：

连通微通道（平行主通道由支流通道连通）流动沸腾传热具有优越的换热性能，但其传热传质强化机理尚不够明确，限制了其实际应用。鉴于此，本文基于流体体积函数（VOF）方法，对连通微通道内过冷流动沸腾进行二维非稳态数值模拟，研究了流场扰动、脱落汽泡与壁面间的薄液膜分布对微通道当地传热系数的影响规律。结果表明，连通微通道存在两种强化换热机理：支流通道脱落汽泡可增强主通道流场扰动，进而促进了通道热边界层再发展；脱落汽泡与热壁面间可形成薄液膜，该薄液膜减小了换热热阻。同时研究了支流通道倾角（θ）对连通微通道强化换热的影响，结果发现，不同θ时，连通微通道整体平均传热系数提高10.51%~17.66%，单个主通道平均传热系数最高可提升27.94%，且θ=45°时连通微通道具有最佳换热特性。该研究有望为芯片高效冷却结构的设计提供指导。

关键词: 连通, 微通道, 流动沸腾, 强化换热, 气液两相流, 数值模拟

Abstract:

The flow boiling of interconnected microchannels, in which main channels are connected by branch channels, has superior heat transfer characteristics. However, the mechanism of heat and mass transfer enhancement is not clear enough, which limits its practical application. Hence, based on the volume of fluid (VOF) method, a two-dimensional unsteady numerical simulation of subcooled flow boiling in the interconnected microchannels was carried out. The influences of local flow field disturbance and thin liquid film distribution between shedding bubbles and heating wall on the heat transfer characteristics of microchannels were discussed. It was found that the mechanisms of heat transfer enhancement contain two types. The first one is that the shedding bubbles of branch channel can enhance the flow field disturbance of main channel, thus promoting the redevelopment of thermal boundary layer of main channel. The second one is that thin liquid film can be formed between shedding bubbles and heating wall, which reduces the heat transfer resistance. The effect of dip angles (θ) of branch channel on the heat transfer characteristics of interconnected microchannels was further studied. It was found that the overall average heat transfer coefficient of interconnected microchannels was improved by 10.51% to 17.66% compared to unconnected microchannels, and the average heat transfer coefficient of single main channel was improved by up to 27.94%. When θ=45°, the interconnected microchannels showed the best heat transfer characteristics. The research could provide guidance for the design of efficient chip cooling structures.

Key words: interconnected, microchannels, flow boiling, enhanced heat transfer, gas-liquid flow, numerical simulation

中图分类号:

TK124

梅响, 姚元鹏, 吴慧英. 连通微通道内过冷流动沸腾传热强化机理分析[J]. 化工进展, 2022, 41(6): 2884-2892.

MEI Xiang, YAO Yuanpeng, WU Huiying. Analysis of heat transfer enhancement mechanism on subcooled flow boiling in interconnected microchannels[J]. Chemical Industry and Engineering Progress, 2022, 41(6): 2884-2892.

图/表 11

参考文献 25

1	COURTLAND R. Moore’s law’s next step: 10 nanometers[J]. IEEE Spectrum, 2017, 54(1): 52-53.
2	BELHARDJ S, MIMOUNI S, SAIDANE A, et al. Using microchannels to cool microprocessors: a transmission-line-matrix study[J]. Microelectronics Journal, 2003, 34(4): 247-253.
3	JIANG L N, KOO J M, WANG E, et al. Cross-linked microchannels for VLSI hotspot cooling[C]//Proceedings of ASME 2002 International Mechanical Engineering Congress and Exposition, 2002, New Orleans, Louisiana, USA. 2008: 13-17.
4	CHO E S, KOO J M, JIANG L N, et al. Experimental study on two-phase heat transfer in microchannel heat sinks with hotspots[C]//Ninteenth Annual IEEE Semiconductor Thermal Measurement and Management Symposium, IEEE, 2003, San Jose, CA, USA. IEEE, 2003: 242-246.
5	XU Jinliang, GAN Yunhua, ZHANG Dingcai, et al. Microscale heat transfer enhancement using thermal boundary layer redeveloping concept[J]. International Journal of Heat and Mass Transfer, 2005, 48(9): 1662-1674.
6	XU Jinliang, ZHANG Wei, WANG Qiuwang, et al. Flow instability and transient flow patterns inside intercrossed silicon microchannel array in a micro-timescale[J]. International Journal of Multiphase Flow, 2006, 32(5): 568-592.
7	MEGAHED A. Experimental investigation of flow boiling characteristics in a cross-linked microchannel heat sink[J]. International Journal of Multiphase Flow, 2011, 37(4): 380-393.
8	汤宇轩, 夏国栋, 宗露香, 等. 间断型波纹微通道内沸腾换热特性研究[J]. 工程热物理学报, 2020, 41(12): 3008-3013.
	TANG Yuxuan, XIA Guodong, ZONG Luxiang, et al. Investigation of boiling heat transfer characteristics in intermittent wavy microchannels[J]. Journal of Engineering Thermophysics, 2020, 41(12): 3008-3013.
9	党超, 贾力, 杞卓琳, 等. 通道结构强化微通道流动沸腾流动与传热[J]. 科学通报, 2019, 64(23): 2450-2462.
	DANG Chao, JIA Li, QI Zhuolin, et al. Flow and heat transfer characteristics of microchannel flow boiling enhancement with channel configurations[J]. Chinese Science Bulletin, 2019, 64(23): 2450-2462.
10	MA Jiaxuan, LI Wenming, REN Congcong, et al. Realizing highly coordinated, rapid and sustainable nucleate boiling in microchannels on HFE-7100[J]. International Journal of Heat and Mass Transfer, 2019, 133: 1219-1229.
11	HUANG Guanghan, LI Wenming, MA Jiaxuan, et al. High-frequency alternating nucleate boiling of water enabled by microslot arrays in microchannels[J]. International Journal of Heat and Mass Transfer, 2020, 150: 119271.
12	CHENG Xiao, WU Huiying. Improved flow boiling performance in high-aspect-ratio interconnected microchannels[J]. International Journal of Heat and Mass Transfer, 2021, 165: 120627.
13	KANDLIKAR S G, KUAN W K, WILLISTEIN D A, et al. Stabilization of flow boiling in microchannels using pressure drop elements and fabricated nucleation sites[J]. Journal of Heat Transfer, 2006, 128(4): 389-396.
14	MORSHED A K M M, YANG F H, YAKUT ALI M, et al. Enhanced flow boiling in a microchannel with integration of nanowires[J]. Applied Thermal Engineering, 2012, 32: 68-75.
15	罗小平, 张超勇, 章金鑫, 等. 针状电极作用下的微细通道流动沸腾传热[J]. 化工进展, 2019, 38(8): 3517-3524.
	LUO Xiaoping, ZHANG Chaoyong, ZHANG Jinxin, et al. Flow boiling heat transfer enhancement in microchannels under needle electrode[J]. Chemical Industry and Engineering Progress, 2019, 38(8): 3517-3524.
16	XU Fayao, WU Huiying, LIU Zhenyu. Flow patterns during flow boiling instability in silicon-based pin-fin microchannels[J]. Journal of Heat Transfer, 2018, 140(3): 031501.
17	杜保周, 李慧君, 郭保仓, 等. 微肋阵通道流动沸腾换热与压降特性[J]. 化工学报, 2018, 69(12): 4979-4989.
	DU Baozhou, LI Huijun, GUO Baocang, et al. Flow boiling heat transfer and pressure drop characteristics in micro channel with micro pin fins[J]. CIESC Journal, 2018, 69(12): 4979-4989.
18	姚鑫宇, 程潇, 王晗, 等. 铜基正弦波微通道内流动沸腾传热特性试验研究[J]. 化工学报, 2020, 71(4): 1502-1509.
	YAO Xinyu, CHENG Xiao, WANG Han, et al. Experimental investigation on flow boiling heat transfer in sinusoidal wavy copper microchannels[J]. CIESC Journal, 2020, 71(4): 1502-1509.
19	HIRT C W, NICHOLS B D. Volume of fluid (VOF) method for the dynamics of free boundaries[J]. Journal of Computational Physics, 1981, 39(1): 201-225.
20	HARDT S, WONDRA F. Evaporation model for interfacial flows based on a continuum-field representation of the source terms[J]. Journal of Computational Physics, 2008, 227(11): 5871-5895.
21	SATO Y, NIČENO B. A sharp-interface phase change model for a mass-conservative interface tracking method[J]. Journal of Computational Physics, 2013, 249: 127-161.
22	RATTNER A S, GARIMELLA S. Simple mechanistically consistent formulation for volume-of-fluid based computations of condensing flows[J]. Journal of Heat Transfer, 2014, 13(7): 071501.
23	LEE W H, LYCZKOWSKI R W. The basic character of five two-phase flow model equation sets[J]. International Journal for Numerical Methods in Fluids, 2000, 33(8): 1075-1098.
24	PRAJAPATI Y K, PATHAK M, KHAN M K. A comparative study of flow boiling heat transfer in three different configurations of microchannels[J]. International Journal of Heat and Mass Transfer, 2015, 85: 711-722.
25	PRAJAPATI Y K, PATHAK M, KHAN M K. Numerical investigation of subcooled flow boiling in segmented finned microchannels[J]. International Communications in Heat and Mass Transfer, 2017, 86: 215-221.

分类	密度/ kg?m^-3	热导率/W?m^-1?K^-1	比热容/J?kg^-1?K^-1	动力黏度/Pa?s	表面张力系数/N?m^-1
液相	961.9	0.682	4214	2.99×10^-4	0.056
气相	0.5542	0.0261	2014	1.34×10^-5	0.056

分类	密度/ kg?m^-3	热导率/W?m^-1?K^-1	比热容/J?kg^-1?K^-1	动力黏度/Pa?s	表面张力系数/N?m^-1
液相	961.9	0.682	4214	2.99×10^-4	0.056
气相	0.5542	0.0261	2014	1.34×10^-5	0.056

θ	上方主通道h₁	下方主通道h₂	连通微通道h_ave	无连通结构微通道h₀	［整体传热系数提升(h_ave-h₀)/h₀］/%
30°	11256.88	10792.16	11024.52	9976.04	10.51
35°	11911.78	10781.72	11346.75		13.74
40°	12562.01	10867.71	11714.86		17.43
45°	12620.77	10854.85	11737.81		17.66
50°	12546.51	10825.35	11685.93		17.14
55°	12627.91	10594.31	11611.11		16.39
60°	12415.86	10562.96	11489.41		15.17
90°	11125.79	11186.63	11156.21		11.83

θ	上方主通道h₁	下方主通道h₂	连通微通道h_ave	无连通结构微通道h₀	［整体传热系数提升(h_ave-h₀)/h₀］/%
30°	11256.88	10792.16	11024.52	9976.04	10.51
35°	11911.78	10781.72	11346.75		13.74
40°	12562.01	10867.71	11714.86		17.43
45°	12620.77	10854.85	11737.81		17.66
50°	12546.51	10825.35	11685.93		17.14
55°	12627.91	10594.31	11611.11		16.39
60°	12415.86	10562.96	11489.41		15.17
90°	11125.79	11186.63	11156.21		11.83

[1]	王太, 苏硕, 李晟瑞, 马小龙, 刘春涛. 交流电场中贴壁气泡的动力学行为[J]. 化工进展, 2023, 42(S1): 133-141.
[2]	赵晨, 苗天泽, 张朝阳, 洪芳军, 汪大海. 负压状态窄缝通道乙二醇水溶液传热特性[J]. 化工进展, 2023, 42(S1): 148-157.
[3]	陈匡胤, 李蕊兰, 童杨, 沈建华. 质子交换膜燃料电池气体扩散层结构与设计研究进展[J]. 化工进展, 2023, 42(S1): 246-259.
[4]	郭强, 赵文凯, 肖永厚. 增强流体扰动强化变压吸附甲硫醚/氮气分离的数值模拟[J]. 化工进展, 2023, 42(S1): 64-72.
[5]	邵博识, 谭宏博. 锯齿波纹板对挥发性有机物低温脱除过程强化模拟分析[J]. 化工进展, 2023, 42(S1): 84-93.
[6]	刘炫麟, 王驿凯, 戴苏洲, 殷勇高. 热泵中氨基甲酸铵分解反应特性及反应器结构优化[J]. 化工进展, 2023, 42(9): 4522-4530.
[7]	赵曦, 马浩然, 李平, 黄爱玲. 错位碰撞型微混合器混合性能的模拟分析与优化设计[J]. 化工进展, 2023, 42(9): 4559-4572.
[8]	卜治丞, 焦波, 林海花, 孙洪源. 脉动热管计算流体力学模型与研究进展[J]. 化工进展, 2023, 42(8): 4167-4181.
[9]	叶振东, 刘涵, 吕静, 张亚宁, 刘洪芝. 基于钙镁二元盐的热化学储能反应器的性能优化[J]. 化工进展, 2023, 42(8): 4307-4314.
[10]	俞俊楠, 俞建峰, 程洋, 齐一搏, 化春键, 蒋毅. 基于深度学习的变宽度浓度梯度芯片性能预测[J]. 化工进展, 2023, 42(7): 3383-3393.
[11]	单雪影, 张濛, 张家傅, 李玲玉, 宋艳, 李锦春. 阻燃型环氧树脂的燃烧数值模拟[J]. 化工进展, 2023, 42(7): 3413-3419.
[12]	王硕, 张亚新, 朱博韬. 基于灰色预测模型的水煤浆输送管道冲蚀磨损寿命预测[J]. 化工进展, 2023, 42(7): 3431-3442.
[13]	周龙大, 赵立新, 徐保蕊, 张爽, 刘琳. 电场-旋流耦合强化多相介质分离研究进展[J]. 化工进展, 2023, 42(7): 3443-3456.
[14]	陈蔚阳, 宋欣, 殷亚然, 张先明, 朱春英, 付涛涛, 马友光. 矩形微通道内液相黏度对气泡界面的作用机制[J]. 化工进展, 2023, 42(7): 3468-3477.
[15]	陶梦琦, 刘美红, 康宇驰. 基于micro-PIV的微通道内流体绕流单微圆柱和并联双微圆柱流场特性[J]. 化工进展, 2023, 42(6): 2836-2844.