化工进展 ›› 2018, Vol. 37 ›› Issue (12): 4701-4708.DOI: 10.16085/j.issn.1000-6613.2018-0261

• 工业催化 • 上一篇    下一篇

Ce掺杂ZnO光催化氧化脱硫性能

梁鹏举1,2, 管荣新1,2, 王伟华2, 秦少伟1,2, 穆金城1,2, 丁慧萍1,2, 姜建辉1,2   

  1. 1 新疆兵团南疆化工资源利用工程实验室, 新疆 阿拉尔 843300;
    2 塔里木大学生命科学学院, 新疆 阿拉尔 843300
  • 收稿日期:2018-01-31 修回日期:2018-06-12 出版日期:2018-12-05 发布日期:2018-12-05
  • 通讯作者: 姜建辉,副教授,硕士生导师,研究方向为光催化材料。
  • 作者简介:梁鹏举(1984-),男,硕士,讲师,研究方向为新型催化材料的制备。E-mail:lpjltx1984@163.com。
  • 基金资助:
    北京化工大学化工资源有效利用国家重点实验室开放项目(CRE-2016-C-202)。

Photocatalytic oxidation desulfurization properties of Ce-doped ZnO

LIANG Pengju1,2, GUAN Rongxin1,2, WANG Weihua2, QIN Shaowei1,2, MU Jincheng1,2, DING Huiping1,2, JIANG Jianhui1,2   

  1. 1 Engineering Laboratory of Chemical Resources Utilization in South Xinjiang of Xinjiang Production and Construction Crops, Alar 843300, Xinjiang, China;
    2 College of Life Sciences, Tarim University, Alar 843300, Xinjiang, China
  • Received:2018-01-31 Revised:2018-06-12 Online:2018-12-05 Published:2018-12-05

摘要: 以水热反应制备前体和随后高温煅烧的方法制得了稀土元素Ce掺杂的ZnO光催化剂。利用X射线衍射、紫外可见、扫描电镜和能谱仪(EDS)对样品进行了物理性质表征,考察了催化剂制备条件、催化剂中Ce、Zn掺杂比和实验条件对催化剂光催化氧化脱硫性能的影响。结果表明,Ce和Zn的摩尔比对Zn(1-xCexO催化剂的光催化氧化脱硫性能有显著影响;最佳条件100℃水热反应4h、300℃煅烧2h,制得的Zn0.89Ce0.11O催化剂在模拟油200mL(含硫量300mg/L)、n(O)/n(S)为39(H2O2 15mL)、催化剂0.3g和紫外光照射1.5h的条件下脱硫率高达98.9%,经过5次再生循环使用后脱硫率没有明显降低。

关键词: 水热合成, 铈, 氧化锌, 光催化, 氧化, 脱硫

Abstract: The rare earth Ce doped ZnO has been prepared with the precursor prepared by hydrothermal method and subsequently calcinated at high temperature. The samples were characterized by X-ray diffraction (XRD), UV-vis, field emission scanning electron microscopy (FESEM) and EDS, respectively. The effects of various experimental parameters on the photocatalytic oxidation desulfurization were investigated. The results showed that the molar ratio of Ce to Zn had significant influence on the photocatalytic oxidation desulfurization properties of the Zn(1-x)CexO catalyst. The optimum preparation parameters were hydrothermal time of 4h at 100℃, calcination treatment of 300℃ at 2h to the Zn0.89Ce0.11O catalyst, 200mL model oil (sulfur content of 300mg/L), n(O)/n(S) molar ratio of 39 (H2O2 15mL), 0.3g catalyst and irradiated under UV-light for 1.5h. The maximum desulfurization rate of the model oil was 98.9% under the above optimum conditions. The desulfurization rate of the catalyst did not decrease obviously after reused for five times.

Key words: hydrothermal method, cerium, zinc oxide, photocatalytic, oxidation, desulfurization

中图分类号: 

京ICP备12046843号-2;京公网安备 11010102001994号
版权所有 © 《化工进展》编辑部
地址:北京市东城区青年湖南街13号 邮编:100011
电子信箱:hgjz@cip.com.cn
本系统由北京玛格泰克科技发展有限公司设计开发 技术支持:support@magtech.com.cn