电火花改性表面池沸腾换热特性

doi:10.16085/j.issn.1000-6613.2018-0399

化工进展 ›› 2018, Vol. 37 ›› Issue (12): 4533-4542.DOI: 10.16085/j.issn.1000-6613.2018-0399

电火花改性表面池沸腾换热特性

何照荣¹, 范志卿¹, 王大成^1,2

1 广东石油化工学院机电工程学院, 广东茂名 525000;
2 广东石油化工学院广东省石油化工装备工程技术研究中心, 广东茂名 525000

收稿日期:2018-02-27 修回日期:2018-08-19 出版日期:2018-12-05 发布日期:2018-12-05
通讯作者: 何照荣(1981-),男,硕士,高级实验师,研究方向为表面改性技术和抗垢功能涂层。
作者简介:何照荣(1981-),男,硕士,高级实验师,研究方向为表面改性技术和抗垢功能涂层。E-mail:hezhaorong@gdupt.edu.cn。
基金资助:
广东省普通高校创新强校特色创新自然科学类项目（2017KTSCX126）、茂名市科技计划（MM2017000003）及广东省石油化工装备工程技术研究中心开放基金（2017JJ517010）项目。

Study on pool boiling heat transfer on modified surface fabricated via electrical discharge machining

HE Zhaorong¹, FAN Zhiqing¹, WANG Dacheng^1,2

1 School of Mechanical and Electrical Engineering, Guangdong University of Petrochemical Technology, Maoming 525000, Guangdong, China;
2 Guangdong Petrochemical Equipment Engineering and Technology Research Center, Maoming 525000, Guangdong, China

Received:2018-02-27 Revised:2018-08-19 Online:2018-12-05 Published:2018-12-05

摘要/Abstract

摘要： 通过电火花成型加工技术在铜基换热表面制备微纳结构改性表面，以自制换热表面性能测试装置进行改性表面的池沸腾换热性能实验。改性表面随加工电流改变而具有不同粗糙度、孔隙率和粗糙度因子，表面接触角范围在117.4°~133.5°。实验结果表明，改性表面的微纳结构提高换热面的池沸腾换热效果，临界热流密度较光滑铜表面提高了26%~87.8%，最大传热系数提高了48.1%~213%。改性表面的传热系数随着粗糙度增大而减小，而临界热流密度则是先增大后减小；孔隙率的增大使得改性表面的传热系数也随之增大，临界热流密度则是随着孔隙率的增大而先增大后减小；临界热流密度随着粗糙度因子的增大而降低，传热系数则是先增大后降低。粗糙度对沸腾换热的强化效果较小，孔隙率和粗糙度因子是强化池沸腾换热的关键，孔隙率和粗糙度因子分别影响了气泡核化密度和实际接触面积，提高了气泡脱离频率，带走更多的热量，但两者间存在互相制约的平衡关系。

关键词: 电火花成型加工, 微纳结构, 池沸腾换热, 粗糙度因子, 表面, 传热

Abstract: Copper based heat exchange surfaces were modified by electrical discharge machining technology. The pool heat exchange properties of modified surfaces were investigated by self-made test device of heat exchange property for heat exchange surface. Due to the change of the machining currents, the roughness, porosity and roughness ratio of the modified surfaces were changed respectively. The contact angles of the modified were 117.4°-133.5°. The results of experiments indicated that the micro and nano structures of modified surfaces enhanced the properties of pool boiling heat exchange. The critical heat flux of modified surfaces was improved 26%-87.8% than that of polished copper surface. The maximum heat transfer coefficients were improved 48.1%-213% than that of polished copper surface. The heat transfer coefficient of modified surfaces decreased with the increase of roughness, and the critical heat flux increased first then decrease later. The increase of porosity of modified surfaces made the heat transfer coefficient increase, but the critical heat flux went up first and then down. The critical heat flux of modified surfaces decreased with the increase of roughness ratio, and the heat transfer coefficient went up and then down later. The effect of the roughness for enhancing pool boil heat transfer was poor. The porosity and roughness ratios were the key facts to enhance the property of pool boiling heat exchange. The porosity affected the bubble nucleation density and the roughness ratio affected actual contact area, which would improve the bubble departure frequency, and more heat flux was taken away from the modified surfaces by the departure bubbles. There was a mutually restrictive balance between porosity and roughness ratio.

Key words: electrical discharge machining, micro and nano structures, pool boiling heat exchange, roughness ratio, surface, heat transfer

中图分类号:

TK124

何照荣, 范志卿, 王大成. 电火花改性表面池沸腾换热特性[J]. 化工进展, 2018, 37(12): 4533-4542.

HE Zhaorong, FAN Zhiqing, WANG Dacheng. Study on pool boiling heat transfer on modified surface fabricated via electrical discharge machining[J]. Chemical Industry and Engineering Progress, 2018, 37(12): 4533-4542.

参考文献

[1] CIESLINSKI T J. Nucleate pool boiling on porous metallic coatings[J]. Experimental Thermal and Fluid Science, 2002,25(7):557-564.
[2] MIN D H,HWANG G S,USTA Y, et al. 2-D and 3-D modulated porous coatings for enhanced pool boiling[J]. International Journal of Heat and Mass Transfer,2009, 52(11/12):2607-2613.
[3] ALI A F, EL-GENK M S. Effect of inclination on saturation boiling of PF-5060 dielectric liquid on 80-and 137-μm thick copper micro-porous surfaces[J]. International Journal of Thermal Sciences, 2012, 53:42-48.
[4] SUN Y, ZHANG L, XU H, et al. Subcooled flow boiling heat transfer from microporous surfaces in a small channel[J]. International Journal of Thermal Sciences, 2011, 50(6):881-889.
[5] 陈宏霞, 黄林滨, 宫逸飞. 多孔结构及表面浸润性对池沸腾传热影响的研究进展[J]. 化工进展, 2017, 36(8):2798-2808. CHEN Hongxia, HUANG Linbin, GONG Yife. Progress on boiling heat transfer from porous structure and surface wettability[J]. Chemical Industry and Engineering Progress, 2017, 36(8):2798-2808.
[6] HEE SEOK A, SATHYAMURTHI V, BANERJEE D. Pool boiling experiments on a nano-structured surface[J]. IEEE Transactions on Components and Packaging Technologies, 2009, 32(1):156-165.
[7] SHOJAEIAN M, KOSAR A. Pool boiling and flow boiling on micro and nano structured surfaces[J]. Experimental Thermal and Fluid Science, 2015, 63:45-73.
[8] NIU G, LI J. Comparative studies of pool boiling heat transfer with nano-fluids on porous surface[J]. Heat and Mass Transfer, 2015, 51(12):1769-1777.
[9] ZHANG B J, KIM K J, YOON H. Enhanced heat transfer performance of alumina sponge-like nano-porous structures through surface wettability control in nucleate pool boiling[J]. International Journal of Heat and Mass Transfer, 2012, 55(25/26):7487-7498.
[10] 柴永志, 张伟, 李亚, 等. 非均匀润湿性微通道表面池沸腾换热特性[J]. 化工学报, 2017, 68(5):1852-1859. CHAI Yongzhi, ZHANG Wei, LI Ya, et al. Pool boiling heat transfer on heterogeneous wetting microchannel surfaces[J]. CIESC Journal, 2017, 68(5):1852-1859.
[11] LI C, WANG Z, WANG P I, et al. Nanostructured copper interfaces for enhanced boiling[J]. Small, 2008, 4(8):1084-1088.
[12] JI X, XU J, ZHAO Z, et al. Pool boiling heat transfer on uniform and non-uniform porous coating surfaces[J]. Experimental Thermal and Fluid Science, 2013, 48:198-212.
[13] 刘阿龙, 徐宏, 王学生, 等. 复合粉末多孔表面管的沸腾传热[J]. 化工学报, 2006, 57(4):726-730. LIU Along, XU Hong, WANG Xuesheng, et al. Boiling heat transfer on composite powder porous surface tubes[J]. CIESC Journal, 2006, 57(4):726-730.
[14] 郭兆阳, 徐鹏, 王元华, 等. 烧结型多孔表面管外池沸腾传热特性[J]. 化工学报, 2012, 63(12):3798-3804. GUO Zhaoyang, XU Peng, WANG Yuanhua, et al. Pool boiling heat transfer on sintered porous coating tubes[J]. CIESC Journal, 2012, 63(12):3798-3804.
[15] YU H, LIAN Z, WAN Y, et al. Fabrication of durable superamphiphobic aluminum alloy surfaces with anisotropic sliding by HS-WEDM and solution immersion processes[J]. Surface and Coatings Technology, 2015, 275:112-119.
[16] LIAN Z, XU J, WENG Z, et al. Research on HS-WEDM and chemical etching technology of superamphiphobic surfaces on Al substrates[J]. Micro and Nano Letters, 2016, 11(8):425-429.
[17] 张超. 冷电极电火花加工温度控制及蚀除机理研究[D]. 南京:南京航空航天大学, 2017. ZHANG Chao. Research on temperature control and removal mechanism by cool electrode of electrical discharge machining[D]. Nanjing:Nanjing University of Aeronautics and Astronautics, 2017.
[18] 张振夫. 钛合金表面微结构电火花加工及其水润滑摩擦学特性研究[D]. 南京:南京航空航天大学, 2009. ZHANG Zhenfu. Surface microstructures on titanium alloy with edm and their tribological properties in water lubrication[D]. Nanjing:Nanjing University of Aeronautics and Astronautics, 2009.
[19] 高绪宝, 顾琳, 赵万生, 等. 混粉电火花加工工件表面质量影响因素分析[J]. 制造业自动化, 2009, 3(3):1-4. GAO Xubao, GU Lin, ZHAO Wansheng, et al. Analysis of the surface integrity generated by the powder-mixed EDM[J]. Manufacturing Automation, 2009, 3(3):1-4.
[20] MUTHURAMALINGAM T, MOHAN B. A review on influence of electrical process parameters in EDM process[J]. Archives of Civil and Mechanical Engineering, 2015, 15(1):87-94.
[21] WENZEL R N. Resistance of solid surfaces to weting by water[J]. Industrial and Engineering Chemistry, 1936, 28(8):988-994.
[22] DONG L, QUAN X, CHENG P. An experimental investigation of enhanced pool boiling heat transfer from surfaces with micro/nano-structures[J]. International Journal of Heat and Mass Transfer, 2014, 71(4):189-196.
[23] PARK Y, KIM H, KIM J, et al. Measurement of liquid-vapor phase distribution on nano-and microstructured boiling surfaces[J]. International Journal of Multiphase Flow, 2016, 81:67-76.
[24] CHAKRABORTY S, DEY V, GHOSH S K. A review on the use of dielectric fluids and their effects in electrical discharge machining characteristics[J]. Precision Engineering, 2015, 40:1-6.
[25] LEE W, SON G. Numerical simulation of boiling enhancement on a microstructured surface[J]. International Communications in Heat and Mass Transfer, 2011, 38(2):168-173.
[26] USTINOV A, USTINOV V, MITROVIC J. Pool boiling heat transfer of tandem tubes provided with the novel microstructures[J]. International Journal of Heat and Fluid Flow, 2011, 32(4):777-784.
[27] JO H, KIM S, KIM H, et al. Nucleate boiling performance on nano/microstructures with different wetting surfaces[J]. Nanoscale Research Letters, 2012, 7(1):242-242.
[28] YOUNG LEE C, HOSSAIN BHUIYA M M, KIM K J. Pool boiling heat transfer with nano-porous surface[J]. International Journal of Heat and Mass Transfer, 2010, 53(19/20):4274-4279.
[29] 郑晓欢, 纪献兵, 王野, 等超亲/疏水性表面池沸腾传热研究[J]. 化工进展, 2016, 35(12):3793-3798. ZHENG Xiaohuan, JI Xianbing, WANG Y, et al. Pool boiling heat transfer on superhydrophilic and superhydrophobic surfaces[J]. Chemical Industry and Engineering Progress, 2016, 35(12):3793-3798.

电火花改性表面池沸腾换热特性

Study on pool boiling heat transfer on modified surface fabricated via electrical discharge machining

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	肖辉, 张显均, 兰治科, 王苏豪, 王盛. 液态金属绕流管束流动传热进展[J]. 化工进展, 2023, 42(S1): 10-20.
[2]	赵晨, 苗天泽, 张朝阳, 洪芳军, 汪大海. 负压状态窄缝通道乙二醇水溶液传热特性[J]. 化工进展, 2023, 42(S1): 148-157.
[3]	张杰, 白忠波, 冯宝鑫, 彭肖林, 任伟伟, 张菁丽, 刘二勇. PEG及其复合添加剂对电解铜箔后处理的影响[J]. 化工进展, 2023, 42(S1): 374-381.
[4]	赵景超, 谭明. 表面活性剂对电渗析减量化工业含盐废水的影响[J]. 化工进展, 2023, 42(S1): 529-535.
[5]	陈林, 徐培渊, 张晓慧, 陈杰, 徐振军, 陈嘉祥, 密晓光, 冯永昌, 梅德清. 液化天然气绕管式换热器壳侧混合工质流动及传热特性[J]. 化工进展, 2023, 42(9): 4496-4503.
[6]	王谨航, 何勇, 史伶俐, 龙臻, 梁德青. 气体水合物阻聚剂研究进展[J]. 化工进展, 2023, 42(9): 4587-4602.
[7]	张振, 李丹, 陈辰, 吴菁岚, 应汉杰, 乔浩. 吸附树脂对唾液酸的分离纯化[J]. 化工进展, 2023, 42(8): 4153-4158.
[8]	卜治丞, 焦波, 林海花, 孙洪源. 脉动热管计算流体力学模型与研究进展[J]. 化工进展, 2023, 42(8): 4167-4181.
[9]	张超, 杨鹏, 刘广林, 赵伟, 杨绪飞, 张伟, 宇波. 表面微结构对阵列微射流沸腾换热的影响[J]. 化工进展, 2023, 42(8): 4193-4203.
[10]	汪健生, 张辉鹏, 刘雪玲, 傅煜郭, 朱剑啸. 多孔介质结构对储层内流动和换热特性的影响[J]. 化工进展, 2023, 42(8): 4212-4220.
[11]	王云刚, 焦健, 邓世丰, 赵钦新, 邵怀爽. 冷凝换热与协同脱硫性能实验分析[J]. 化工进展, 2023, 42(8): 4230-4237.
[12]	张凯, 吕秋楠, 李刚, 李小森, 莫家媚. 南海海泥中甲烷水合物的形貌及赋存特性[J]. 化工进展, 2023, 42(7): 3865-3874.
[13]	杨扬, 孙志高, 李翠敏, 李娟, 黄海峰. 静态条件下表面活性剂OP-13促进HCFC-141b水合物生成[J]. 化工进展, 2023, 42(6): 2854-2859.
[14]	刘厚励, 顾中浩, 阳康, 张莉. 3D打印槽道结构槽宽对池沸腾传热特性的影响[J]. 化工进展, 2023, 42(5): 2282-2288.
[15]	张晨宇, 王宁, 徐洪涛, 罗祝清. 纳米颗粒强化传热的多级潜热储热器性能评价[J]. 化工进展, 2023, 42(5): 2332-2342.