固体碱渣解聚均质器结构试验与数值模拟

doi:10.16085/j.issn.1000-6613.2017-1769

化工进展 ›› 2018, Vol. 37 ›› Issue (06): 2101-2108.DOI: 10.16085/j.issn.1000-6613.2017-1769

固体碱渣解聚均质器结构试验与数值模拟

赵斌¹, 高明非¹, 杜亚杰^1,2, 霍殿龙²

1 华北理工大学冶金与能源学院, 河北唐山 063210;
2 唐山思扬科技有限公司, 河北唐山 063000

收稿日期:2017-08-22 修回日期:2017-11-16 出版日期:2018-06-05 发布日期:2018-06-05
通讯作者: 赵斌(1968-),男,博士,教授,研究方向为两相流。
作者简介:赵斌(1968-),男,博士,教授,研究方向为两相流。E-mail:zhaobin19680507@163.com。

Experimental study and numerical simulation of solid alkaline slag depolymerization homogenizer structure

ZHAO Bin¹, GAO Mingfei¹, DU Yajie^1,2, HUO Dianlong²

1 College of Metallurgy and Energy, North China University of Science and Technology, Tangshan 063210, Hebei, China;
2 Tangshan Siyang Technology Co., Ltd., Tangshan 063000, Hebei, China

Received:2017-08-22 Revised:2017-11-16 Online:2018-06-05 Published:2018-06-05

摘要/Abstract

摘要： 制碱工业过程产生大量碱渣等废弃物，固体碱渣再利用是化工行业技术难题。本文以某化工股份有限公司氨碱法制碱过程中产生的固体碱渣为研究对象，数值模拟研究了影响均质器内浆液分布均匀性的变化因素，通过试验验证了均质器的最佳结构特征。结果表明：固体碱渣的粒度小，具有溶胶的性质，经过压滤机压滤过后的碱渣，粒子重新团聚，硬度大、不易破碎、解聚；提高均质器的搅拌器转速对流体的流动速度及均质效果有很大改善，但并不能完全消除死区；相比于局部立式搅拌桨叶结构，采用立式搅拌桨结构的均质效果明显，且功耗更小；增加导流板结构，与未加装前相比，功耗降低，综合考虑确定均质器的搅拌器采用立式桨+平直桨+导流板的混合型桨叶结构，有利于提高碱渣再利用的经济性。本文研究结果可为固体碱渣制备脱硫剂的工业应用奠定基础。

关键词: 固体碱渣, 均质器, 结构优化, 试验研究, 数值模拟

Abstract: During the ammonia alkali process, a lot of caustic waste such as alkaline slag is produced. It is a technical problem in the chemical industry to solve the waste of alkali residue. Taking a chemical Co. Ltd., solid alkaline slag production during the ammonia alkaline process as the research object, the effects of homogenized fluid distribution uniformity were numerically studied. The optimum structural characteristics of homogenizer were verified by experiments. The results showed that, the particle size of solid alkaline slag is small, which has the same properties of sol. After filter presser, the particle of alkaline slag reunites, which make it has high hardness and hard to break and homogenate. It has great effect on fluid flow when increasing the rotation speed of blender, but the dead zone cannot be completely eliminated. Compared with the local-vertical blade structure, the homogeneity effect of vertical blade structure is more obvious, and the power consumption is smaller. Increasing the structure of the deflector, the power consumption reduces compared to before loading. Overall consideration, the blade structure of homogenizer blender adopt plan of horizontal-blade + vertical-blade + guide plate, which is helpful to improve the economy of the reuse of alkali residue. The research can build the foundation for the industrial application of desulfurizer for solid alkaline slag.

Key words: solid alkaline slag, desulfurizer preparation, structure optimization, experiment research, numerical simulation

中图分类号:

TQ074

赵斌, 高明非, 杜亚杰, 霍殿龙. 固体碱渣解聚均质器结构试验与数值模拟[J]. 化工进展, 2018, 37(06): 2101-2108.

ZHAO Bin, GAO Mingfei, DU Yajie, HUO Dianlong. Experimental study and numerical simulation of solid alkaline slag depolymerization homogenizer structure[J]. Chemical Industry and Engineering Progress, 2018, 37(06): 2101-2108.

参考文献

[1] 谢文玉,钟理,陈建军,等. 用循环曝气生物滤池工艺处理炼油碱渣废水[J]. 化工学报, 2008, 59(1):214-220. XIE W Y, ZHONG L, CHEN J J, et al. Treatment of spent caustic wastewater from petroleum refinery using circulating biological aerated filter process[J]. Journal of Chemical Industry and Engineering (China), 2008, 59(1):214-220.
[2] 韩昌亮,任婧杰,王焱庆,等. SCV耦合传热特性实验研究与数值模拟[J]. 化工学报, 2017, 68(3):854-863. HAN C L, REN J J, WANG Y Q, et al. Experimental study and numerical simulation on coupled heat transfer characteristics of submerged combustion vaporizer[J]. Journal of Chemical Industry and Engineering(China), 2017, 68(3):854-863.
[3] 赵建立,樊兆燕,李英杰,等. 碱性工业废渣在湿法脱硫中的消溶特性[J]. 煤炭学报, 2011, 36(4):676-680. ZHAO J L, FAN Z Y, LI Y J, et al. Dissolution characteristics of alkaline industrial wastes in wet flue gas desulphurization[J]. Journal of the China Coal Society, 2011, 36(4):676-680.
[4] 赵建立,韩奎华,樊兆燕,等. 碱性工业废渣湿法烟气脱硫性能研究[J]. 电站系统工程, 2011, 27(1):36-40. ZHAO J L, HAN K H, FAN Z Y, et al. Characteristics of alkahne industrial wastes in wet fiue gas desulphurization[J]. Power System Engineering, 2011, 27(1):36-40.
[5] CHEN D S, ZHAO L S, TAO Q I, et al. Desilication from titanium-vanadium slag by alkaline leaching[J]. Transactions of Nonferrous Metals Society of China, 2013, 23(10):3076-3082.
[6] GUO C, ZHANG Y, QIAO S, et al. Leaching technology and kinetics of vanadium from vanadium and chromium-bearing slag by alkaline process[J]. The Chinese Journal of Process Engineering, 2015, 15(3):400-405.
[7] ZHANG F, ZHOU R, LI L, et al. Modification of attapulgite clay for desulfurizer preparation[J]. Environmental Pollution & Control, 2009, 57(5):636-642.
[8] ZHENG X R, JIN Q M, HE R Y, et al. Impact analysis of support to Zn based desulfurizer prepared by high pressure impregnation method[J]. Journal of the China Coal Society, 2011, 36(11):1911-1916.
[9] MAHMOUDKHANI M, RICHARDS T, THELIANDER H. Use of kraft recovery cycle residuals in mineralization of forestscontrolling leaching rates of cimited soluble species[J]. Tappi Joumal, 2005, 4(7):31-33.
[10] HAKANSSON A, TRAGARDH C, BERGENSTAHL B. Dynamic simulation of emulsion formation in a high pressure homogenizer[J]. Chemical Engineering Science, 2009, 64(12):2915-2925.
[11] VARCOE J R, SLADE R C T. An electron-beam-grafted ETFE alkaline anion-exchange membrane in metal-cation-free solid-state alkaline fuel cells[J]. Electrochemistry Communications, 2006, 8(5):839-843.
[12] 刘洪涛,韩奎华,李辉,等. 赤泥调质石灰石用作循环流化床锅炉固硫剂的研究[J]. 热力发电, 2012, 41(9):13-17. LIU H T, HAN K H, LI H, et al. Sulfur retention performance of limestone modified by red mud for CFB boiler[J]. Thermal Power Generation, 2012, 41(9):13-17.
[13] 马晓燕,许普查. 利用固体废物研制新型固硫剂[J]. 洁净煤技术, 2008, 14(1):70-72. MA X Y, XU P C. Study on additives for sulfur fixed with solid rubbish[J]. Clean Coal Technology, 2008, 14(1):70-72.
[14] 王秉钧,耿县如,刘忠华,等. 碱渣综合利用制备液体脱硫剂技术研究[J]. 纯碱工业, 2015(6):12-15. WANG B J, GENG X R, LIU Z H, et al. Technical study on preparation of liquid desulfurizer by synthesis of alkaline slag[J]. Soda Industry, 2015(6):12-15.
[15] 芮玉兰,梁英华,王彦艳. 碱渣用于模拟烟气湿式脱硫的研究[J]. 环境科学与技术, 2006, 29(7):21-22. RUI Y L, LIANG Y H, WANG Y Y. Wet simulation flue gas desulfurization with sodaash dregs absorbent[J]. Environmental Science and Technology, 2006, 29(7):21-22.
[16] 王华,李光明,张蓓. 滴流床反应器催化湿式氧化法处理碱渣废水[J]. 化工进展, 2007, 26(2):221-225. WANG H, LI G M, ZHANG B. Catalytic wet oxidation of spent caustic wastewater in trickle bed reactor[J]. Chemical Industry and Engineering Progress, 2007, 26(2):221-225.
[17] 杨巧文,赵昕伟,滕玉奇,等. 燃煤复合废渣固硫剂的固硫试验研究[J]. 煤炭科学技术, 2015, 43(8):153-157. YANG Q W,ZHAO X W,TENG Y Q,et al. Study on sulfur fixed experiment compound residue sulfur fixative in coal combustion[J]. Coal Science and Technology, 2015, 43(8):153-157.
[18] 韩奎华,赵建立,郑斌,等. 碱性废渣用于煤燃烧固硫的性能与改性[J]. 煤炭学报, 2009, 34(12):1697-1702. HAN K H, ZHAO J L, ZHENG B, et al. Sulfur retention performance and modification of alkaline wastes used in coal combustion[J]. Journal of the China Coal Society, 2009, 34(12):1697-1702.
[19] 朱全力. 潮州瓷土矿复合碱性金属化合物对无烟煤粉燃烧与固硫的影响[J]. 燃烧科学与技术, 2014, 20(2):141-146. ZHU L Q. Effect of alkaline metal -comtaining composite with Chaozhou porcelain clay on the combustion and sulfur retention of anthracite coal powders[J]. Journal of Combustion Science and Technology, 2014, 20(2):141-146.
[20] PARAMGURU R K, RATH P C, MISRA V N. Trends in red mudutilization-a review[J]. Mineral Processing and Extractive Metallurgy Review, 2005, 26(1):1-29.
[21] YU Q C, DENG Y, WANG F, et al. Preparation of activated ceria and its desulfurization performance[J]. International Joural of Minerals, Metallurgy and Materials, 2015, 9(22):992-997.

固体碱渣解聚均质器结构试验与数值模拟

Experimental study and numerical simulation of solid alkaline slag depolymerization homogenizer structure

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	王太, 苏硕, 李晟瑞, 马小龙, 刘春涛. 交流电场中贴壁气泡的动力学行为[J]. 化工进展, 2023, 42(S1): 133-141.
[2]	陈匡胤, 李蕊兰, 童杨, 沈建华. 质子交换膜燃料电池气体扩散层结构与设计研究进展[J]. 化工进展, 2023, 42(S1): 246-259.
[3]	郭强, 赵文凯, 肖永厚. 增强流体扰动强化变压吸附甲硫醚/氮气分离的数值模拟[J]. 化工进展, 2023, 42(S1): 64-72.
[4]	邵博识, 谭宏博. 锯齿波纹板对挥发性有机物低温脱除过程强化模拟分析[J]. 化工进展, 2023, 42(S1): 84-93.
[5]	刘炫麟, 王驿凯, 戴苏洲, 殷勇高. 热泵中氨基甲酸铵分解反应特性及反应器结构优化[J]. 化工进展, 2023, 42(9): 4522-4530.
[6]	赵曦, 马浩然, 李平, 黄爱玲. 错位碰撞型微混合器混合性能的模拟分析与优化设计[J]. 化工进展, 2023, 42(9): 4559-4572.
[7]	叶振东, 刘涵, 吕静, 张亚宁, 刘洪芝. 基于钙镁二元盐的热化学储能反应器的性能优化[J]. 化工进展, 2023, 42(8): 4307-4314.
[8]	俞俊楠, 俞建峰, 程洋, 齐一搏, 化春键, 蒋毅. 基于深度学习的变宽度浓度梯度芯片性能预测[J]. 化工进展, 2023, 42(7): 3383-3393.
[9]	单雪影, 张濛, 张家傅, 李玲玉, 宋艳, 李锦春. 阻燃型环氧树脂的燃烧数值模拟[J]. 化工进展, 2023, 42(7): 3413-3419.
[10]	王硕, 张亚新, 朱博韬. 基于灰色预测模型的水煤浆输送管道冲蚀磨损寿命预测[J]. 化工进展, 2023, 42(7): 3431-3442.
[11]	周龙大, 赵立新, 徐保蕊, 张爽, 刘琳. 电场-旋流耦合强化多相介质分离研究进展[J]. 化工进展, 2023, 42(7): 3443-3456.
[12]	张晨宇, 王宁, 徐洪涛, 罗祝清. 纳米颗粒强化传热的多级潜热储热器性能评价[J]. 化工进展, 2023, 42(5): 2332-2342.
[13]	卢兴福, 戴波, 杨世亮. 转鼓内圆柱形颗粒混合的超二次曲面离散单元法模拟[J]. 化工进展, 2023, 42(5): 2252-2261.
[14]	马润梅, 杨海超, 李正大, 李双喜, 赵祥, 章国庆. 表面强化镀层对高速轴承腔密封端面变形及摩擦磨损影响分析[J]. 化工进展, 2023, 42(4): 1688-1697.
[15]	张成松, 张静, 龚斌, 李明洋, 袁佳新, 李宏业. 自吸射流柔性搅拌桨振动特性[J]. 化工进展, 2023, 42(4): 1728-1738.