高热流密度器件水冷散热器结构性能的实验研究

doi:10.16085/j.issn.1000-6613.2016.05.012

化工进展 ›› 2016, Vol. 35 ›› Issue (05): 1338-1343.DOI: 10.16085/j.issn.1000-6613.2016.05.012

高热流密度器件水冷散热器结构性能的实验研究

崔卓, 诸凯, 王雅博, 魏杰

天津商业大学机械工程学院, 天津 300110

收稿日期:2015-11-10 修回日期:2015-12-15 出版日期:2016-05-05 发布日期:2016-05-05
通讯作者: 王雅博,讲师,研究方向为强化传热传质。E-mail wang_yabo@tju.edu.c。
作者简介:崔卓(1990-),男,硕士研究生。
基金资助:
国家自然科学基金(51376137)及天津市自然科学基金(13JCZDJC27300)项目。

Experimental study on water-cooled radiator structure performance of high heat flux device

CUI Zhuo, ZHU Kai, WANG Yabo, WEI Jie

School of Mechanical Engineering, Tianjin University of Commerce, Tianjin 300110, China

Received:2015-11-10 Revised:2015-12-15 Online:2016-05-05 Published:2016-05-05

摘要/Abstract

摘要： 与平行流水冷散热相比,现阶段对喷射流水冷散热的研究报道较少。为了研究喷射流结构的散热效果,本文设计了两种喷射流结构的水冷散热器,搭建了以去离子水为冷却介质的液冷散热器实验台,调节实验的热流密度及冷却水流量在不同条件下观察芯片温度及散热器底板温度的变化,得到了不同热流密度下芯片温度、散热器底板温度及热阻随冷却水流量的变化规律。散热器内部针翅结构和冷却水流动方式的改变可使芯片温度降低5~8℃,散热器底板平均温度也相应降低4℃左右,且底板温度梯度较小。同时,热阻的变化随流量增大逐渐变缓,散热器结构改进使热阻减小了7%~8%。实验结果表明,改进结构的散热器能有效加强边角区域流体的扰动,提升散热器整体的换热效率,表明喷射流水冷散热是一种高效的散热方式。

关键词: 传热, 传质, 对流, 针柱, 水冷散热器

Abstract: Compared with parallel flow cooling, the report of impinging jet cooling has rarely be seen. To study the heat dissipation performance of impinging jet cooling, two radiator were designed in this study. Test bench was built. The cooling medium was deionized water. The temperature variations of CPU chip and radiator bottom plate in different condition were measured by changing the heat flux and cooling water flow. The temperature change of CPU chip and radiator bottom plate was analyzed. By monitoring the inner fin structure anf flow direction of cooling water, the average temperature of CPU could drop 5 to 8℃ and 4℃ for the radiator bottom plate. In addition, the variation range of heat resistance was diminished gradually with the increase of cooling flow. Heat resistance of radiator reduced by 7%-8% due to improvement of radiator structure. The results showed that improvement of radiator structure effectively strengths the disturbance of the corner area and increases heat transfer efficiency of radiator. The present study indicates that impinging jet cooling is a high efficiency radiating way.

Key words: heat transfer, mass transfer, convection, pin fin, water-cooled heat sink

中图分类号:

TK172

崔卓, 诸凯, 王雅博, 魏杰. 高热流密度器件水冷散热器结构性能的实验研究[J]. 化工进展, 2016, 35(05): 1338-1343.

CUI Zhuo, ZHU Kai, WANG Yabo, WEI Jie. Experimental study on water-cooled radiator structure performance of high heat flux device[J]. Chemical Industry and Engineering Progree, 2016, 35(05): 1338-1343.

参考文献

[1] SAHITI H, DURST F, DEWAN A. Heat transfer enhancement by pin elements[J]. International Journal of Heat and Mass Transfer, 2005, 48(23/24): 4738-4747.
[2] SAHITI N, LEMOUEDDA A, STOJKOVIC D, et al. Performance comparison of pin fin in-duct flow arrays with various pin cross-sections[J]. Applied Thermal Engineering, 2006, 26(11/12): 1176-1192.
[3] CHYU M K, SIW S C, MOON H K.Effects of height-to-diameter ratio of pin element on heat transfer from staggere Pin-Fin arrays, [M]. Florida: ASEM, 2009: 705-713.
[4] BRIGHAM B A, VANFOSSEN G J. Length of diameter ratio and row number effects in short pin fin heat transfer[J]. Journal of Engineering for Gas Turbines and Power, 1984, 104: 241-244.
[5] VANFOSSEN G J. Heat transfer coefficients for staggered arrays of short pin-fins[J]. Journal of Engineering for Gas Turbines and Power, 1982, 102: 268-274.
[6] PANDIT Jaideep, THOMPSON Megan, EKKAD Srinich V, et al. Effect of pin fin to channel ratio and pin fin geometry on heat transfer performance for flow in rectangular channels[J]. International Journal of Heat and Mass Transfer, 2014, 77: 359-368.
[7] DESHMUKH P A, WARKHEDDAR R M. Thermal performance of elliptical pin fin heat sink under combined natural and forced convection[J]. Experimental Thermal and Fluid Science, 2013, 50: 61-68.
[8] 丁杰, 何多昌, 唐玉兔. 翅柱式水冷散热器的性能研究[J]. 大功率变流技术, 2013, 28(7): 32-36.
[9] CORMIER Yannick, DUPIUS Philippe, FARGAM Aslan, et al. Additive manufacturing of pyramidal pin fins: Height and density effects under forced convection[J]. International Journey of Heat and Mass Transfer, 2014, 75: 235-244.
[10] TULLIUS J F, TULLIUS T K, BAYAZITOGLU Y. Optimization of short micro pin fins in minichannels[J]. International Journal of Heat and Mass Transfer, 2012, 55(15/16): 3921-3932.
[11] 牛永红, 刘宗攀, 庞赟佶. CPU芯片水冷散热器的数值模拟与分析[J]. 化工进展, 2010, 29(s1): 653-655.

[1]	肖辉, 张显均, 兰治科, 王苏豪, 王盛. 液态金属绕流管束流动传热进展[J]. 化工进展, 2023, 42(S1): 10-20.
[2]	盛维武, 程永攀, 陈强, 李小婷, 魏嘉, 李琳鸽, 陈险峰. 微气泡和微液滴双强化脱硫反应器操作分析[J]. 化工进展, 2023, 42(S1): 142-147.
[3]	赵晨, 苗天泽, 张朝阳, 洪芳军, 汪大海. 负压状态窄缝通道乙二醇水溶液传热特性[J]. 化工进展, 2023, 42(S1): 148-157.
[4]	黄益平, 李婷, 郑龙云, 戚傲, 陈政霖, 史天昊, 张新宇, 郭凯, 胡猛, 倪泽雨, 刘辉, 夏苗, 主凯, 刘春江. 三级环流反应器中气液流动与传质规律[J]. 化工进展, 2023, 42(S1): 175-188.
[5]	杨寒月, 孔令真, 陈家庆, 孙欢, 宋家恺, 王思诚, 孔标. 微气泡型下向流管式气液接触器脱碳性能[J]. 化工进展, 2023, 42(S1): 197-204.
[6]	陈匡胤, 李蕊兰, 童杨, 沈建华. 质子交换膜燃料电池气体扩散层结构与设计研究进展[J]. 化工进展, 2023, 42(S1): 246-259.
[7]	邵博识, 谭宏博. 锯齿波纹板对挥发性有机物低温脱除过程强化模拟分析[J]. 化工进展, 2023, 42(S1): 84-93.
[8]	陈林, 徐培渊, 张晓慧, 陈杰, 徐振军, 陈嘉祥, 密晓光, 冯永昌, 梅德清. 液化天然气绕管式换热器壳侧混合工质流动及传热特性[J]. 化工进展, 2023, 42(9): 4496-4503.
[9]	卜治丞, 焦波, 林海花, 孙洪源. 脉动热管计算流体力学模型与研究进展[J]. 化工进展, 2023, 42(8): 4167-4181.
[10]	汪健生, 张辉鹏, 刘雪玲, 傅煜郭, 朱剑啸. 多孔介质结构对储层内流动和换热特性的影响[J]. 化工进展, 2023, 42(8): 4212-4220.
[11]	王云刚, 焦健, 邓世丰, 赵钦新, 邵怀爽. 冷凝换热与协同脱硫性能实验分析[J]. 化工进展, 2023, 42(8): 4230-4237.
[12]	李洞, 王倩倩, 张亮, 李俊, 付乾, 朱恂, 廖强. 非水系纳米流体热再生液流电池串联堆性能特性[J]. 化工进展, 2023, 42(8): 4238-4246.
[13]	李瑞东, 黄辉, 同国虎, 王跃社. 原油精馏塔中铵盐吸湿特性及其腐蚀行为[J]. 化工进展, 2023, 42(6): 2809-2818.
[14]	章凯, 金捍宇, 刘思宇, 王帅. 鼓泡流态化气泡间相互作用下相间传质过程的模拟[J]. 化工进展, 2023, 42(6): 2828-2835.
[15]	马哲杰, 张文励, 赵炫凯, 李平. PEMFC阴极催化层氧传质阻力影响的研究进展[J]. 化工进展, 2023, 42(6): 2860-2873.

高热流密度器件水冷散热器结构性能的实验研究

Experimental study on water-cooled radiator structure performance of high heat flux device

PDF (PC)

可视化

被引次数

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价