化工进展 ›› 2019, Vol. 38 ›› Issue (11): 5015-5023.DOI: 10.16085/j.issn.1000-6613.2019-0049

• 材料科学与技术 • 上一篇    下一篇

磷铁渣制备电池级纳米磷酸铁

马毅1,2,3(),沈文喆1,2,3,袁梅梅1,2,3,王韵珂1,2,3,姚耀春1,2,3()   

  1. 1. 昆明理工大学冶金与能源工程学院,云南 昆明 650093
    2. 节能与新能源汽车动力电池及关键材料研究中心,云南 昆明 650093
    3. 昆明理工大学真空冶金国家工程实验室,云南 昆明 650093
  • 收稿日期:2019-01-09 出版日期:2019-11-05 发布日期:2019-11-05
  • 通讯作者: 姚耀春
  • 作者简介:马毅(1992—),男,硕士研究生,研究方向为新能源材料。E-mail:1872903434@qq.com
  • 基金资助:
    国家自然科学基金(51364021)

Preparation of battery grade nano iron phosphate by using ferro-phosphorus as raw material

Yi MA1,2,3(),Wenzhe SHEN1,2,3,Meimei YUAN1,2,3,Yunke WANG1,2,3,Yaochun YAO1,2,3()   

  1. 1. Faculty of Metallurgical and Energy Engineering, Kunming University of Science and Technology, Kunming 650093, Yunnan, China
    2. Energy Saving and New Energy Automobile Power Battery and Key Materials Research Center, Kunming 650093, Yunnan, China
    3. National Engineering Laboratory for Vacuum Metallurgy, Kunming 650093, Yunnan, China
  • Received:2019-01-09 Online:2019-11-05 Published:2019-11-05
  • Contact: Yaochun YAO

摘要:

以磷铁废渣为原料提供磷源和铁源,用硝酸和硫酸混合溶液浸出磷铁渣中的铁和磷元素,并通过沉淀法制备电池级纳米磷酸铁。探究了硝酸浓度、反应时间、反应温度对磷铁渣溶解率的影响,并研究了反应过程中铁磷比、温度和pH对制备的磷酸铁性能影响。利用X衍射分析仪、扫描电子显微镜、热重分析仪、红外光谱仪和电感耦合等离子体发射光谱仪等分析手段对磷酸铁的形貌、晶体结构与化学成分进行了表征。实验结果表明,磷铁渣浸出最佳的实验条件为:硝酸浓度1.5mol/L,反应时间4h,反应温度90℃,此条件下磷铁的溶解率为95.11%;磷酸铁制备过程中的最佳实验条件为:铁磷比1∶1,反应温度60℃,反应pH=1.0,所制备的FePO4结晶度高,颗粒形貌规整,分散均匀,一次颗粒粒径为100~200nm,铁磷摩尔比为0.97,杂质元素含量符合电池级磷酸铁的要求。

关键词: 磷酸铁, 磷铁渣, 沉淀, 结晶, 溶解, 纳米, 制备

Abstract:

Ferro-phosphorus was used as the iron source and the phosphorus source and the ferro-phosphorus was dissolved in the mixture of nitric acid and sulfuric acid, and battery-grade nano-iron phosphate was prepared by precipitation method. The influence of the concentration of nitric acid, the reaction time and temperature on the dissolving rate of ferro-phosphorus was studied. The effects of the ratio of iron and phosphorus, reacting temperature and pH on the performance of the FePO4 were also explored. The crystal morphology, structure and chemical composition of the prepared nanoscale iron(Ⅲ) phosphate were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), thermogravimetric, differential scanning calorimetry (TG-DSC), infrared spectrometer, and inductively coupled plasma atomic emission spectrometer(ICP-AES). Experimental results show that the optimum experimental conditions for the dissolving of ferro-phosphorus areas follows: nitric acid concentration 1.5mol/L, reaction time 4h, reaction temperature 90℃, under which the dissolution rate of iron phosphate is 95.1%. The optimal conditions for the preparation of iron phosphate are: iron-phosphorus ratio 1∶1, reaction temperature 60℃, reaction pH 1.0. XRD and SEM analysis showed that the prepared FePO4 had high crystallinity, and regular morphology, uniform particle dispersion, its primary particle size is around 100nm. The iron and phosphorus content test shows that the molar ratio of iron to phosphorus was 0.97. The content of impurity elements meets the requirement of battery grade FePO4 precursor.

Key words: iron(Ⅲ) phosphate, ferro-phosphorus, precipitation, crystallization, dissolution, nano, preparation

中图分类号: 

京ICP备12046843号-2;京公网安备 11010102001994号
版权所有 © 《化工进展》编辑部
地址:北京市东城区青年湖南街13号 邮编:100011
电子信箱:hgjz@cip.com.cn
本系统由北京玛格泰克科技发展有限公司设计开发 技术支持:support@magtech.com.cn