化工进展 ›› 2016, Vol. 35 ›› Issue (07): 1963-1968.DOI: 10.16085/j.issn.1000-6613.2016.07.004

• 化工过程与装备 • 上一篇    下一篇

不同工况下除湿溶液再生的模拟与实验

邹国文1, 邹同华1, 韩雨松1, 邓赛峰1, 曹国振2   

  1. 1. 天津商业大学天津市制冷技术重点实验室, 天津 300134;
    2. 郑州宇通重工有限公司, 河南 郑州 451482
  • 收稿日期:2015-11-27 修回日期:2016-02-04 出版日期:2016-07-05 发布日期:2016-07-05
  • 通讯作者: 邹同华,男,副教授,硕士生导师,主要研究方向为食品冷链技术及制冷空调节能与优化。E-mail:zthua@tjcu.edu.cn。
  • 作者简介:邹国文(1987-),男,硕士研究生,主要从事溶液除湿研究。E-mail:zou881118@163.con。

Simulation and experimental study on regeneration of desiccant solution on different conditions

ZOU Guowen1, ZOU Tonghua1, HAN Yusong1, DENG Saifeng1, CAO Guozhen2   

  1. 1. Tianjin Key Laboratory of Refrigeration Technology, Tianjin University of Commerce, Tianjin 300134, China;
    2. Zhengzhou Yutong Heavy Industries Co., Ltd., Zhengzhou 451482, Henan, China
  • Received:2015-11-27 Revised:2016-02-04 Online:2016-07-05 Published:2016-07-05

PDF (PC)

410

摘要： 建立了LiCl溶液再生过程的数学模型,通过模拟分析,得到了溶液再生量、溶液温度和溶液浓度随时间的变化规律。以平均再生量为评价指标,对LiCl溶液的再生性能进行了实验研究。分析了热源温度、溶液浓度、溶液初始温度、再生压力和冷水温度5个因素分别对溶液再生性能的影响规律。实验结果表明:溶液浓度和再生压力对溶液再生性能影响显著,冷水温度对溶液再生性能的影响最小。在设定的标准工况下,再生压力为4kPa、溶液中LiCl质量分数从28%增大到34%时,平均再生量由20.45g/(m2·s)减小至7.44g/(m2·s);再生压力从4kPa升高至10kPa时,平均再生量由15.33g/(m2·s)降低至1.92g/(m2·s)。最后,以溶液温度和溶液浓度作为对比目标参数将模拟结果和实验结果进行了对比分析,结果表明,实验值与模拟值符合较好。

关键词: 溶液再生, 真空技术, 数值模拟, 平均再生量

Abstract: The mathematical model of regeneration process of lithium chloride water solution was built in this paper. Variation of average moisture removal rate, temperature and concentration of solution with time were obtained by simulation analysis. Experimental study of regeneration performance of lithium chloride water solution was carried out using average moisture removal rate as the evaluation index. Influence trends of temperature of hot water , concentration of solution, initial temperature of solution, regeneration pressure, and temperature of cold water these five factors on regeneration performance were analysed, respectively. Experimental results showed that concentration of solution, pressure of regeneration have significant impact on regeneration performance, temperature of cold water has a weak influence on regeneration performance. At standard operating conditions, the pressure of regeneration is 4 kPa. When the mass fraction of LiCl in solution increased from 28% to 34%, the average moisture removal rate decreased from 20.45g/ (m2·s) to 7.44g/ (m2·s). When pressure of regeneration increased from 4kPa to 10kPa, the average moisture removal rate decreased from 15.33g/ (m2·s) to 1.92g/ (m2·s). At last, both simulation and experimental results using temperature and concentration of solution as target parameters were compared and analysed. Results showed that simulation and experimental values are in a good agreement.

Key words: solution renewable, vacuum technology, numerical simulation, average moisture removal rate

中图分类号: 

京ICP备12046843号-2；京公网安备 11010102001994号
版权所有 © 《化工进展》编辑部
地址：北京市东城区青年湖南街13号　邮编：100011
电子信箱：hgjz@cip.com.cn
本系统由北京玛格泰克科技发展有限公司设计开发　技术支持：support@magtech.com.cn