化工进展 ›› 2022, Vol. 41 ›› Issue (11): 5977-5985.DOI: 10.16085/j.issn.1000-6613.2022-0183

• 材料科学与技术 • 上一篇    下一篇

硫酸钠水合盐相变蓄冷材料的制备及性能优化

杨晋1(), 殷勇高1(), 陈万河1, 王静远1, 陈九法2   

  1. 1.东南大学能源与环境学院,江苏 南京 210096
    2.南京紫金山智慧城市研究院有限公司,江苏 南京 210096
  • 收稿日期:2022-02-06 修回日期:2022-04-19 出版日期:2022-11-25 发布日期:2022-11-28
  • 通讯作者: 殷勇高
  • 作者简介:杨晋(1997—),女,硕士研究生,研究方向为相变蓄冷。E-mail:EUGENIA7_21@163.com

Preparation and performance optimization of phase change cold storage materials with sodium sulfate hydrate salt

YANG Jin1(), YIN Yonggao1(), CHEN Wanhe1, WANG Jingyuan1, CHEN Jiufa2   

  1. 1.School of Energy and Environment, Southeast University, Nanjing 210096, Jiangsu, China
    2.Nanjing Purple Mountain Smart City Research Institute Co. , Nanjing 210096, Jiangsu, China
  • Received:2022-02-06 Revised:2022-04-19 Online:2022-11-25 Published:2022-11-28
  • Contact: YIN Yonggao

摘要:

针对空调系统应用场合,提出一种以十水硫酸钠(sodium sulfate decahydrate,SSD)为主材的相变蓄冷材料新型制备配方,并对材料的各方面性能加以优化。首先采用步冷曲线法确定成核剂比例,消除材料过冷现象,在此基础上研究分析了不同种类、含量的增稠剂[聚丙烯酸钠(PAAS)、聚丙烯酰胺(PAM)、羧甲基纤维素(CMC)、聚阴离子纤维素(PAC)、黄原胶(XG)]对材料相分离及相变潜热的影响,接着加入熔点控制剂氯化铵、氯化钾改变十水硫酸钠的相变温度,调配出满足空调温区的相变材料,最后加入膨胀石墨(expanded graphite,EG)进一步改善材料的导热性和稳定性,并进行了热循环测试。结果表明:添加质量分数3%的硼砂对降低材料过冷度效果最佳;添加质量分数1.0%~2.0%的PAAS可以消除材料的相分离现象,且对材料的相变潜热影响较小。SSD-BPA∶EG质量比为93∶7时材料具有较高的导热性和形状稳定性。经优化后复合相变蓄冷材料的相变温度为7.4℃,相变潜热为117.4J/g,热导率为1.876W/(m·K),经200次循环后材料的相变温度保持稳定,潜热衰减率为14.05%。

关键词: 相变材料, 蓄冷, 十水硫酸钠, 相变温度, 相变潜热

Abstract:

A new formulation for the preparation of phase change cold storage materials based on sodium sulfate decahydrate (SSD) was proposed for air-conditioning system applications, and all aspects of the material's performance were optimized. The nucleating agent ratio was first determined using the step-cooling curve method to eliminate subcooling of the material. On this basis, the effect of different types and levels of thickening agents [sodium polyacrylate (PAAS), polyacrylamide (PAM), carboxymethyl cellulose (CMC), polyanionic cellulose (PAC) and xanthan gum (XG)] on the phase separation and latent heat of phase change of the material was investigated and analyzed. Then, the melting point controller ammonium chloride and potassium chloride were added to change the phase change temperature of sodium sulfate decahydrate, and the phase change material was formulated to meet the air-conditioning temperature zone. Finally, expanded graphite (EG) was added to further improve the thermal conductivity and stability of the material, and the thermal cycling tests were carried out. The experimental results showed that the addition of 3% (mass fraction) borax was the most effective in reducing the subcooling of the material. The addition of 1.0%—2.0% (mass fraction) PAAS could eliminate the phase separation phenomenon of the material and had the less effect on the latent heat of phase change of the material. The material had a high thermal conductivity and shape stability when the mass ratio of SSD-BPA∶EG was 93∶7. The phase change temperature of the optimized composite phase change storage material was 7.4℃, the latent heat of phase change was 117.4J/g and the thermal conductivity was 1.876W/(m·K). The phase change temperature of the material remains stable after 200 cycles and the latent heat decay rate was 14.05%.

Key words: phase change materials, cold storage, sodium sulfate decahydrate, phase change temperature, latent heat of phase change

中图分类号: 

京ICP备12046843号-2;京公网安备 11010102001994号
版权所有 © 《化工进展》编辑部
地址:北京市东城区青年湖南街13号 邮编:100011
电子信箱:hgjz@cip.com.cn
本系统由北京玛格泰克科技发展有限公司设计开发 技术支持:support@magtech.com.cn