翅柱式水冷CPU芯片散热器冷却与流动性能

doi:10.16085/j.issn.1000-6613.2017.06.009

化工进展 ›› 2017, Vol. 36 ›› Issue (06): 2031-2037.DOI: 10.16085/j.issn.1000-6613.2017.06.009

翅柱式水冷CPU芯片散热器冷却与流动性能

王彬, 诸凯, 王雅博, 刘圣春, 魏杰

天津商业大学天津市制冷技术重点实验室, 天津 300134

收稿日期:2016-10-31 修回日期:2017-03-06 出版日期:2017-06-05 发布日期:2017-06-05
通讯作者: 诸凯
作者简介:王彬(1991—),男,硕士研究生,研究方向为强化传热。E-mail:wangbinxlp@126.com。
基金资助:
国家自然科学基金项目（51376137）。

Experimental study on cooling and flow performance of water-cooling radiator with different pin-fins structures for CPU cooling

WANG Bin, ZHU Kai, WANG Yabo, LIU Shengchun, WEI Jie

Tianjin Key Laboratory of Refrigeration Technology, Tianjin University of Commerce, Tianjin 300134, China

Received:2016-10-31 Revised:2017-03-06 Online:2017-06-05 Published:2017-06-05

摘要/Abstract

摘要： 如何在增强散热效果的同时降低阻力损失已成为解决中央处理器（CPU）芯片水冷散热问题的关键。本文从翅柱数量、分布、结构以及冷却流体进出口方式等方面对3种水冷散热器进行实验研究，分别在控制冷却流体流量和热流密度的条件下比较不同翅柱结构的压力损失、芯片温度及散热器热阻，得知散热器四角带有导流结构以及水滴形翅柱结构的散热器在热流密度为80W/cm²、流量为20mL/s时，芯片温度分别为65.5℃和55.5℃，其热阻分别为0.19K/W和0.14K/W，散热性能均优于传统圆柱形翅柱散热器。在流量为60mL/s时，圆柱形翅柱散热器四角设置导流板及水滴形翅柱结构散热器的进出口压力损失分别为34kPa和32kPa，压力损失均小于传统圆柱形翅柱散热器。实验表明在圆柱形翅柱散热器的四角设置导流板，或者改变翅柱形状为水滴形，不仅可强化对流换热，而且可降低流动阻力。

关键词: 传热, 对流, 流体力学, 水冷散热器, 热阻

Abstract: Heat dissipation performance and flow resistance of the traditional circular pin-fins radiator,the cylindrical column fins radiator with fluid guide plates at four corners and hydrofoil pin-fins radiator were studied by changing heat flux and cooling water flow. The pressure drop,chip temperature and thermal resistance of three radiators were measured under the same conditions. The results showed that the chip temperature of the radiator with fluid guide plates at four corners and hydrofoil pin-fins radiator are 65.5℃ and 55.5℃,respectively. The thermal resistance are 0.19K/W and 0.14K/W,respectively at heat flux of 80W/cm² and flow rate of 20mL/s. The heat dissipation performance is better than traditional circular pin-fins radiator. At 60mL/s,the pressure drop of the cylindrical column fins radiator with fluid guide plates at four corners and hydrofoil pin-fins are 34kPa and 32kPa,respectively,which is less than traditional circular pin-fins radiator. Compared with the traditional one,the cylindrical column fins radiator with fluid guide plates at four corners and hydrofoil pin-fins radiator have better heat dissipation performance and smaller pressure drop.

Key words: heat transfer, convection, fluid mechanics, water-cooling radiator, thermal resistance

中图分类号:

TK172

王彬, 诸凯, 王雅博, 刘圣春, 魏杰. 翅柱式水冷CPU芯片散热器冷却与流动性能[J]. 化工进展, 2017, 36(06): 2031-2037.

WANG Bin, ZHU Kai, WANG Yabo, LIU Shengchun, WEI Jie. Experimental study on cooling and flow performance of water-cooling radiator with different pin-fins structures for CPU cooling[J]. Chemical Industry and Engineering Progress, 2017, 36(06): 2031-2037.

参考文献

[1] WHELAN B P,KEMPERS R,ROBINSON A J. A liquid-based system for CPU cooling implementing a jet array impingement waterblock and a tube array remote heat exchanger[J]. Applied Thermal Engineering,2012,39(3):86-94.
[2] SAUCIUC I,PRASHER R,CHANG J Y,et al. Thermal performance and key challenges for future CPU cooling technologies[C]//Advances in Electronic Packaging 2005,Pts A-C. 2005:353-364.
[3] 郝俊娇,潘日,周刚,等. 高热流密度电子元件中热管散热技术的进展[J]. 化工进展,2015,34(5):1220-1224. HAO J J,PAN R,ZHOU G,et al. Development of heat pipe cooling technology in high heat flux electronic components[J]. Chemical Industry and Engineering Progress,2015,34(5):1220-1224.
[4] SHARMA C S,TIWARI M K,ZIMMERMANN S,et al. Energy efficient hotspot-targeted embedded liquid cooling of electronics[J]. Applied Energy,2015,138:414-422.
[5] 牛永红,刘宗攀,庞赟佶. CPU芯片水冷散热器的数值模拟与分析[J]. 化工进展,2010,29(s1):653-655. NIU Y H,LIU Z P,PANG Y J. Numerical simulation and analysis of CPU chip water-cooling radiator[J]. Chemical Industry and Engineering Progress,2010,29(s1):635-655.
[6] 夏国栋,刘青,王敏,等. 岐管式微通道冷却热沉的三维数值优化[J]. 工程热物理学报,2006,27(1):145-147. XIA G D,LIU Q,WANG M,et al. Three-dimensional numerical optimization of the manifold microchannel heat sink[J]. Journal of Engineering Thermophysics,2006,27(1):145-147.
[7] 崔卓,诸凯,王雅博,等. 高热流密度器件水冷散热器结构性能的实验研究[J]. 化工进展,2016,35(5):1338-1343. CUI Z,ZHU K,WANG Y B,et al. Experimental study on water-cooled radiator structure performance of high heat flux device[J]. Chemical Industry and Engineering Progress,2016,35(5):1338-1343.
[8] LIU S,YANG J,GAN Z,et al. Structural optimization of a microjet based cooling system for high power LEDs[J]. International Journal of Thermal Sciences,2008,47(8):1086-1095.
[9] ZHAO J,HUANG S,GONG L,et al. Numerical study and optimizing on micro square pin-fin heat sink for electronic cooling[J]. Applied Thermal Engineering,2016,93:1347-1359.
[10] NDAO S,PELES Y,JENSEN M K. Effects of pin fin shape and configuration on the single-phase heat transfer characteristics of jet impingement on micro pin fins[J]. International Journal of Heat and Mass Transfer,2014,70:856-863.
[11] CHEIN R,HUANG G. Thermoelectric cooler application in electronic cooling[J]. Applied Thermal Engineering,2004,24(14/15):2207-2217.
[12] Moffat R J. Describing the uncertainties in experimental results[J]. Experimental Thermal and Fluid Science,1988,1(1):3-17.
[13] 代宝民. CO₂/低GWP工质二元混合物微小通道内流动换热机理的研究[D]. 天津:天津大学,2015. DAI B M. Research on heat transfer mechanism of CO₂/low-GWP refrigerant binary mixtures flowing in micro- and mini-channels[D]. Tianjin:Tianjin University,2015.
[14] 周明正,夏国栋,柴磊,等. 流体横掠水滴形微针肋热沉流动和传热特性[J]. 航空动力学报,2012,27(12):2681-2686. ZHOU M Z,XIA G D,CAI L,et al. Flow and heat transfer characteristics of drop-shaped micro pin-fin heat sinks with cross flow[J]. Journal of Aerospace Power,2012,27(12): 2681-2686.
[15] SINGH R,AKBARZADEH A,DIXON C,et al. Miniature loop heat pipe with flat evaporator for cooling computer CPU[J]. IEEE Transactions on Components and Packaging Technologies,2007,30(1):42-49.

翅柱式水冷CPU芯片散热器冷却与流动性能

Experimental study on cooling and flow performance of water-cooling radiator with different pin-fins structures for CPU cooling

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	王云飞, 秦蕊, 郑利军, 李焱, 李清平. 旋转填充床CFD模拟研究进展[J]. 化工进展, 2023, 42(S1): 1-9.
[2]	肖辉, 张显均, 兰治科, 王苏豪, 王盛. 液态金属绕流管束流动传热进展[J]. 化工进展, 2023, 42(S1): 10-20.
[3]	赵晨, 苗天泽, 张朝阳, 洪芳军, 汪大海. 负压状态窄缝通道乙二醇水溶液传热特性[J]. 化工进展, 2023, 42(S1): 148-157.
[4]	孙继鹏, 韩靖, 唐杨超, 闫汉博, 张杰瑶, 肖苹, 吴峰. 硫黄湿法成型过程数值模拟与操作参数优化[J]. 化工进展, 2023, 42(S1): 189-196.
[5]	李春利, 韩晓光, 刘加朋, 王亚涛, 王晨希, 王洪海, 彭胜. 填料塔液体分布器的研究进展[J]. 化工进展, 2023, 42(9): 4479-4495.
[6]	陈林, 徐培渊, 张晓慧, 陈杰, 徐振军, 陈嘉祥, 密晓光, 冯永昌, 梅德清. 液化天然气绕管式换热器壳侧混合工质流动及传热特性[J]. 化工进展, 2023, 42(9): 4496-4503.
[7]	徐茂淯, 陶帅, 齐聪, 梁林. 圆盘式环路热管的启动特性及温度波动[J]. 化工进展, 2023, 42(9): 4531-4537.
[8]	罗成, 范晓勇, 朱永红, 田丰, 崔楼伟, 杜崇鹏, 王飞利, 李冬, 郑化安. 中低温煤焦油加氢反应器不同分配器中液体分布的CFD模拟[J]. 化工进展, 2023, 42(9): 4538-4549.
[9]	卜治丞, 焦波, 林海花, 孙洪源. 脉动热管计算流体力学模型与研究进展[J]. 化工进展, 2023, 42(8): 4167-4181.
[10]	张超, 杨鹏, 刘广林, 赵伟, 杨绪飞, 张伟, 宇波. 表面微结构对阵列微射流沸腾换热的影响[J]. 化工进展, 2023, 42(8): 4193-4203.
[11]	汪健生, 张辉鹏, 刘雪玲, 傅煜郭, 朱剑啸. 多孔介质结构对储层内流动和换热特性的影响[J]. 化工进展, 2023, 42(8): 4212-4220.
[12]	王云刚, 焦健, 邓世丰, 赵钦新, 邵怀爽. 冷凝换热与协同脱硫性能实验分析[J]. 化工进展, 2023, 42(8): 4230-4237.
[13]	陶梦琦, 刘美红, 康宇驰. 基于micro-PIV的微通道内流体绕流单微圆柱和并联双微圆柱流场特性[J]. 化工进展, 2023, 42(6): 2836-2844.
[14]	刘厚励, 顾中浩, 阳康, 张莉. 3D打印槽道结构槽宽对池沸腾传热特性的影响[J]. 化工进展, 2023, 42(5): 2282-2288.
[15]	陈伟良, 高鑫, 李洪, 李鑫钢. 泡沫碳化硅波纹规整填料骨架结构对其传质性能的影响机理[J]. 化工进展, 2023, 42(5): 2289-2297.