Chemical Industry and Engineering Progree ›› 2015, Vol. 34 ›› Issue (10): 3700-3705.DOI: 10.16085/j.issn.1000-6613.2015.10.028

Previous Articles     Next Articles

Colloidal silica/PDMS pervaporation membranes for pervaporative separation of n-butanol from aqueous solution

TANG Jun, CHEN Deqiang, ZHANG Chunfang, BAI Yunxiang, GU Jin, SUN Yuping   

  1. The Key Laboratory of Food Colloids and Biotechnology, Ministry of Education, School of Chemical and Materials Engineering, Jiangnan University, Wuxi 214122, Jiangsu, China
  • Received:2014-12-16 Revised:2015-02-13 Online:2015-10-05 Published:2015-10-05

硅溶胶/PDMS渗透汽化膜的制备及分离水中正丁醇

唐郡, 陈德强, 张春芳, 白云翔, 顾瑾, 孙余凭   

  1. 江南大学化学与材料工程学院食品胶体与生物技术教育部重点实验室, 江苏 无锡 214122
  • 通讯作者: 孙余凭,教授,主要从事膜材料制备及应用研究。E-mailsunyp2003@163.com。
  • 作者简介:唐郡(1989—),女,硕士研究生,主要从事膜应用研究。E-mailtangtravel@163.com。
  • 基金资助:

    江苏省产学研前瞻性联合研究项目(BY2013015-06)。

Abstract: Based on the emulsion film forming technology, colloidal silica/PDMS hybrid membranes were prepared with colloidal silica as filler, and used for the pervaporative separation of n-butanol from aqueous solution. The membranes were analyzed by FI-IR, and characterized with morphology, thermal stability, contact angle, and mechanical property. The effect of colloidal silica content on membrane pervaporative performance was studied. The results showed that the incorporation of colloidal silica improved the pervaporative performance obviously; colloidal silica combined with PDMS substrates very well, and there was no obvious phase interface. At 40℃, feed concentration of 1%, with an increase of colloidal silica content, both n-butanol/water selectivity and permeability for n-butanol increased first and then decreased. When the colloidal silica content is 3.75%, the selectivity was the highest, and reached 9.03; while permeability for n-butanol reached the highest, 2.9×106Barrer, when the content is 7.5%.

Key words: membranes, colloidal silica, emulsions, hyperbranched polysiloxane, pervaporation

摘要: 基于乳液成膜技术,以硅溶胶为填充剂,制备了硅溶胶聚二甲基硅氧烷/PDMS杂化膜,用于分离水中正丁醇。对膜进行了FI-IR分析及形貌、热稳定性、接触角和力学性能表征;研究了硅溶胶的加入对膜渗透汽化性能的影响。结果表明,硅溶胶与PDMS基质结合良好,没有明显相界面,膜的渗透汽化性能明显提高。在料液质量分数为1%、操作温度为40℃时,随着膜中硅溶胶含量的增加,膜的分离选择性和对丁醇的渗透性均呈现先升高后下降的趋势;在硅溶胶含量为3.75%时,分离选择性高达9.03;在硅溶胶含量为7.5%时,膜对丁醇的渗透性高达2.9×106Barrer。

关键词: 膜, 硅溶胶, 乳液, 超支化聚硅氧烷, 渗透汽化

CLC Number: 

京ICP备12046843号-2;京公网安备 11010102001994号
Copyright © Chemical Industry and Engineering Progress, All Rights Reserved.
E-mail: hgjz@cip.com.cn
Powered by Beijing Magtech Co. Ltd