化工进展 ›› 2019, Vol. 38 ›› Issue (08): 3640-3649.DOI: 10.16085/j.issn.1000-6613.2018-2457

• 能源加工与技术 • 上一篇    下一篇

基于段塞流捕捉的高黏油气两相流模型的建立与验证

李爽1(),李玉星1(),王冬旭1,王权2   

  1. 1. 中国石油大学(华东) 山东省油气储运安全省级重点实验室,山东 青岛 266580
    2. 中国市政工程中南设计研究总院有限公司,湖北 武汉 430060
  • 收稿日期:2018-12-22 出版日期:2019-08-05 发布日期:2019-08-05
  • 通讯作者: 李玉星
  • 作者简介:李爽(1995—),男,硕士研究生,研究方向为气液两相流。E-mail:z17060596@s.upc.edu.cn
  • 基金资助:
    国家自然科学基金面上项目(51774313);国家重点研发计划(2016YFC0802104)

Development and verification of model based on slug flow capturing for high-viscosity oil and gas two-phase flow

Shuang LI1(),Yuxing LI1(),Dongxu WANG1,Quan WANG2   

  1. 1. Provincial Key Laboratory of Oil and Gas Storage and Transportation Security, China University of Petroleum (East China), Qingdao 266580, Shandong, China
    2. Central and Southern China Municipal Engineering Design & Research Institute, Wuhan 430060, Hubei, China
  • Received:2018-12-22 Online:2019-08-05 Published:2019-08-05
  • Contact: Yuxing LI

摘要:

随着传统油田的快速消耗,高黏稠油的开发逐渐引起了重视。有关高黏油的气液两相流研究主要集中在国外,国内的相关研究目前还较少。本文针对高黏油气混输管路,建立了一种捕捉段塞流的形成和发展过程,并进行两相流水力计算和液塞长度统计的组合模型。通过气液相间滑移速度和液相连续性方程的求解得到管路中不同时刻和位置的持液率,以持液率的变化反映段塞的形成和发展。建立气液动量守恒方程关联持液率和压力,得到管路中各位置的压力变化。闭合关系式中,通过液塞平移速度、壁面及气液相界面的剪切力关系式加入黏度的影响,最终建立适用于高黏油气两相流的段塞捕捉模型。使用不同来源的数据验证模型计算压降和液塞长度的准确性,数据分别来源于国外研究者的实验数据和大庆油田的现场数据。结果表明,模型具有较高的计算精度,大部分压降误差在±15%以内,大部分液塞长度误差在±20%以内。

关键词: 气液两相流, 高黏油, 模型, 段塞流, 水力计算

Abstract:

Heavy oil, an unconventional fossil fuel with high viscosity is increasingly becoming important due to the rapid depletion of conventional oil fields. The study on high viscosity oil and gas two-phase flow is mainly concentrated in abroad, domestic related researches are still few. A combined model was proposed to capture the initiation and development and calculate hydraulic parameters for high viscosity oil and gas multiphase pipeline. The change of liquid holdup at different times and positions was obtained with the solving of slip velocity equation and liquid continuity equation and by which the initiation and development of the slug were reflected. For obtaining the change of pressure in pipeline, the momentum equation was developed to correlate the liquid holdup and pressure. In closed correlations, the influence of viscosity was added using the slug translational velocity and the interfacial shear stress. Finally, a slug capturing model suitable for high-viscosity oil and gas two-phase flow was developed. The accuracy of the model was verified by data from different sources. The data were derived from the experimental data of foreign researchers and the field data of Daqing Oilfield. The results showed that the model has fine calculation accuracy, the relative errors of most pressure drop calculated were within ±15%, and the relative errors of most slug length calculated were within ±20%.

Key words: gas-liquid two-phase flow, high-viscosity oil, model, slug flow, hydraulic calculation

中图分类号: 

京ICP备12046843号-2;京公网安备 11010102001994号
版权所有 © 《化工进展》编辑部
地址:北京市东城区青年湖南街13号 邮编:100011
电子信箱:hgjz@cip.com.cn
本系统由北京玛格泰克科技发展有限公司设计开发 技术支持:support@magtech.com.cn