气固两相流固相浓度与流速的测量及可视化

doi:10.16085/j.issn.1000-6613.2016-2459

化工进展 ›› 2017, Vol. 36 ›› Issue (12): 4350-4355.DOI: 10.16085/j.issn.1000-6613.2016-2459

气固两相流固相浓度与流速的测量及可视化

田海军¹, 周云龙², 赵晓明¹

1 东北电力大学自动化工程学院, 吉林吉林 132012;
2 东北电力大学能源与动力工程学院, 吉林吉林 132012

收稿日期:2017-01-03 修回日期:2017-05-11 出版日期:2017-12-05 发布日期:2017-12-05
作者简介:田海军(1971-),男,工学硕士,高级实验师,主要从事过程检测及层析成像方面的研究工作。E-mail:thaijun_72@126.com。
基金资助:
国家自然科学基金项目（51276033）。

Measurement and visualization of concentration and velocity of solid phase in the gas-solid two-phase flow

TIAN Haijun¹, ZHOU Yunlong², ZHAO Xiaoming¹

1 School of Automation Engineering, Northeast Electric Power University, Jilin 132012, Jilin, China;
2 School of Energy and Power Engineering, Northeast Electric Power University, Jilin 132012, Jilin, China

Received:2017-01-03 Revised:2017-05-11 Online:2017-12-05 Published:2017-12-05

摘要/Abstract

摘要： 气固两相流固相流率的测量是测试领域的难点之一，为了实现气固两相流固相浓度与流速的测量，阐述了电容层析成像的原理，搭建了气固两相流实验台，固相选用聚丙烯颗粒，气相为空气，固相依靠自身的重力流经实验装置，利用ITS公司的M3C电容层析成像装置对气固两相流的固相浓度、速度、质量流量进行了测试研究。实验中的浓度测量采用图像的介电常数分布像素，速度测量选择双层结构的电容传感器，利用相关测速原理，计算上下游传感器成像像素的相关性，最后由测得的速度及浓度分布计算出质量流量，测量结果与重力传感器测量的质量流量结果进行了对比，结果具有较好的一致性，测量误差小于10%，表明利用电容层析成像系统可对气固两相流参数的测量。

关键词: 成像, 两相流, 流动, 质量流量, 固相浓度, 浓度, 体积流量

Abstract: Measurement of the solid phase flow rate in the gas-solid two-phase flow is one of the difficulties in test realm. In order to realize visualization measurement of gas-solid two phase flow, the principle of electrical capacitance tomography was stated and a gas-solid two phase flow test-bed was developed. Polypropylene particles and air were selected as the solid phase and gas phase. Solid phase relied on their own gravity flow through experimental device. M3C capacitance tomography device of ITS company was used for the test and research on solid phase concentration, speed and mass flow rate in the gas-solid two phase flow. In the experiment,concentration measurement was based on the dielectric constant distribution of the pixels about image. Capacitive sensor with double layer structure was used to measure velocity. The relevant principles of the speed measurement was used to compute the correlation between upstream and downstream of sensor imaging pixel. Finally, the mass flow was calculated by the measured velocity and concentration distributions. The mass flow measurements were compared with the results of gravity sensor. The results showed good agreement with measurement error of less than 10%. The experimental results indicated that the capacitance tomography system can be used to measure the parameters of gas-solid two phase flow.

Key words: image, two-phase flow, flow, mass flow, solid concentration, concentration, volume flow

中图分类号:

TP29

田海军, 周云龙, 赵晓明. 气固两相流固相浓度与流速的测量及可视化[J]. 化工进展, 2017, 36(12): 4350-4355.

TIAN Haijun, ZHOU Yunlong, ZHAO Xiaoming. Measurement and visualization of concentration and velocity of solid phase in the gas-solid two-phase flow[J]. Chemical Industry and Engineering Progress, 2017, 36(12): 4350-4355.

参考文献

[1] 漆海峰,郭晓镭,陆海峰,等. 煤粉的流动性测试及评价方法[J]. 化工学报,2012,63(2):434-440. QI H F,GUO X L,LU H F,et al. Measurement of flowability of coal powders and research methods[J]. CIESC Journal,2012,63(2):434-440.
[2] 徐越,吴一宁,危师让. 二段式干煤粉气流床气化技术的模拟研究与分析[J].中国电机工程学报,2003,23(10):187-190. XU Y,WU Y N,WEI S R. Simulation and analysis on gasification technology of a two-stage dry feed entrained flow bed[J]. Proceedings of the CSEE,2003,23(10):187-190.
[3] 田昌,苏明旭,蔡小舒. 基于超声法测量气固两相流浓度实验研究[J].工程热物理学报,2013,34(8):1487-1490. TIAN C,SU M X,CAI X S. Particle concentration characterization in gas-solid two-phase flow by ultrasonic methods[J]. Journal of Engineering Thermophysics,2013,34(8):1487-1490.
[4] 秦授轩,蔡小舒. 在线测量煤粉粒度分布和浓度的实验研究[J]. 中国电机工程学报,2010,30(32):30-34. QIN S X,CAI X S. Experimental study on in-line measurement of size distribution and concentration of pulverized coal parameter[J]. Chinese Journal of Scientific Instrument,2010,30(32):30-34.
[5] 陆海峰,郭晓镭,陶顺龙,等. 电容层析成像在煤粉料仓下料中的应用[J]. 化工学报,2014,65(2):422-428. LU H F,GUO X L,TAO S L,et al. Application of electrical capacitance tomography in hopper discharge of pulverized coal[J]. CIESC Journal,2014,65(2):422-428.
[6] 贺春辉,沈湘林,周海军. 煤粉高压密相气力输送稳定性分析[J].化工学报,2014,65(3):820-827. HE C H,SHEN X L,ZHOU H J. Stability analysis of dense phase pneumatic conveying of pulverized coal at high pressure[J]. CIESC Journal,2014,65(3):820-827.
[7] 王超,王玉琳,张文彪. 基于静电传感的气固两相流测量及研究装置[J]. 电子测量与仪器学报,2011,25(1):1-9. WANG C,WANG Y L,ZHANG W B. Gas-solid two-phase flow measurement and research apparatus based on electrostatic sensing[J]. Journal of Electronic Measurement and Instrument,2011,25(1):1-9.
[8] 陆海峰,郭晓镭,陶顺龙,等. 电容层析成像在煤粉料仓下料中的应用[J]. 化工学报,2014,65(2):422-428. LU H F,GUO X L,TAO S L,et al. Application of electrical capacitance tomography in hopper discharge of pulverized coal[J]. CIESC Journal,2014,65(2):422-428.
[9] 王海刚,赵国荣,邱桂芝. 循环流化床多旋风分离器入口电容层析成像测量[J]. 工程热物理学报,2014,35(1):109-113. WANG H G,ZHAO G R,QIU G Z. Investigation the solid phase distribution in the inlet of multi-cyclone of a circulating fluidized bed by electrical capacitance tomography[J]. Journal of Engineering Thermophysics,2014,35(1):109-113.
[10] 杨道业,郭瑞,王晓荣,等. 电容层析成像在滑动轴承润滑油膜测量中的应用[J]. 中国电机工程学报,2012,32(5):187-190. YANG D Y,GUO R,WANG X R,et al. Application of electrical capacitance tomography on lubricating oil film in journal bearings[J]. Proceedings of the CSEE,2012,32(5):187-190.
[11] CHEN L J,WANG H,WANG K Q,et al. The confirmation of wavelet base and decomposition progression in wood texture analysis[J]. Forestry Machinery & Woodworking Equipment,2007,35(2):25-27.
[12] MOSOROV V. Flow pattern tracing for mass flow rate measurement in pneumatic conveying using twin plane electrical capacitance tomography[J]. Particle & Particle Systems Characterization, 2008,25(3):259-265.
[13] GEWEKE M,GADE U. Pneumatic conveying with turbuflow-advantages against conventional dense phase conveying[J]. Handbook of Powder Technology,2001,10(1):395-401.
[14] ZHENG Y,LIU Q. Review of techniques for the mass flow rate measurement of pneumatically conveyed solids[J]. Measurement,2011,44(4):589-604.
[15] 鹿鹏,韩东,蒲文灏,等. 高压密相气力输送煤粉输送速率通量及神经网络模拟[J]. 化工学报,2013,64(5):1607-1613. LU P,HAN D,PU W H,et al. Solids flux of pulverized coal of high-pressure and dense-phase pneumatic conveying and ANN simulation[J]. CIESC Journal,2013,64(5):1607-1613.
[16] MOHD S T,AHMAD A H,SITI K K,et al. Electrical resistance tomography investigation of gas dispersion in gas-liquid mixing in an agitated vessel[J]. Journal of Applied Sciences,2009,9(17):3110-3115.
[17] MA Aichun,WILLIAMS Kenneth C,ZHOU Jiemin,et al. Experimental and numerical research on pressure gradient of a pneumatic conveying pipeline of flyash[C]//International Conference on Intelligent System Design & Engineering Application. IEEE Computer Society,2012:1247-1250.
[18] CHEN L J,WANG H,WANG K Q,et al. The confirmation of wavelet base and decomposition progression in wood texture analysis[J]. Forestry Machinery & Woodworking Equipment,2007,35(3):25-27.
[19] YANG W Q,LIU S. Role of tomography in gas/solid flow measurement[J]. Flow Measurement and Instrumentation,2000,11(3):237-244.
[20] BECK M S. Correlation in instruments——Cross correlation flowmeters[J]. Journal of Physics E:Scientific Instruments,2000,14(1):7-19.

气固两相流固相浓度与流速的测量及可视化

Measurement and visualization of concentration and velocity of solid phase in the gas-solid two-phase flow

PDF (PC)

可视化

被引次数

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	徐若思, 谭蔚. C形管池沸腾两相流流场模拟与流固耦合分析[J]. 化工进展, 2023, 42(S1): 47-55.
[2]	赵晨, 苗天泽, 张朝阳, 洪芳军, 汪大海. 负压状态窄缝通道乙二醇水溶液传热特性[J]. 化工进展, 2023, 42(S1): 148-157.
[3]	陈匡胤, 李蕊兰, 童杨, 沈建华. 质子交换膜燃料电池气体扩散层结构与设计研究进展[J]. 化工进展, 2023, 42(S1): 246-259.
[4]	陈林, 徐培渊, 张晓慧, 陈杰, 徐振军, 陈嘉祥, 密晓光, 冯永昌, 梅德清. 液化天然气绕管式换热器壳侧混合工质流动及传热特性[J]. 化工进展, 2023, 42(9): 4496-4503.
[5]	罗成, 范晓勇, 朱永红, 田丰, 崔楼伟, 杜崇鹏, 王飞利, 李冬, 郑化安. 中低温煤焦油加氢反应器不同分配器中液体分布的CFD模拟[J]. 化工进展, 2023, 42(9): 4538-4549.
[6]	吕程远, 张函, 杨明旺, 杜健军, 樊江莉. 生物成像用二氧杂环丁烷余辉发光体系的研究进展[J]. 化工进展, 2023, 42(8): 4108-4122.
[7]	卜治丞, 焦波, 林海花, 孙洪源. 脉动热管计算流体力学模型与研究进展[J]. 化工进展, 2023, 42(8): 4167-4181.
[8]	王硕, 张亚新, 朱博韬. 基于灰色预测模型的水煤浆输送管道冲蚀磨损寿命预测[J]. 化工进展, 2023, 42(7): 3431-3442.
[9]	陈蔚阳, 宋欣, 殷亚然, 张先明, 朱春英, 付涛涛, 马友光. 矩形微通道内液相黏度对气泡界面的作用机制[J]. 化工进展, 2023, 42(7): 3468-3477.
[10]	孙征楠, 李洪晶, 荆国林, 张福宁, 颜飚, 刘晓燕. EVA及其改性聚合物在原油降凝剂领域的应用[J]. 化工进展, 2023, 42(6): 2987-2998.
[11]	郭文杰, 翟玉玲, 陈文哲, 申鑫, 邢明. Al₂O₃-CuO/水混合纳米流体对流传热性能及热经济性分析[J]. 化工进展, 2023, 42(5): 2315-2324.
[12]	袁守正, 陈啸, 蒋鸣, 余亚雄, 周强. 气固下行床中壁面对介尺度曳力的影响规律[J]. 化工进展, 2023, 42(5): 2272-2281.
[13]	刘厚励, 顾中浩, 阳康, 张莉. 3D打印槽道结构槽宽对池沸腾传热特性的影响[J]. 化工进展, 2023, 42(5): 2282-2288.
[14]	王文昊, 何立东, 王学志, 闫泽, 贾兴运, 刘春瑞. 偏心工况下梳齿、蜂窝与蜂窝-梳齿密封的泄漏特性[J]. 化工进展, 2023, 42(4): 1698-1707.
[15]	庞力平, 袁虎, 丘文生, 段立强, 李文学. 深度调峰锅炉水动力特性分析[J]. 化工进展, 2023, 42(4): 1708-1718.