化工进展 ›› 2017, Vol. 36 ›› Issue (10): 3584-3589.DOI: 10.16085/j.issn.1000-6613.2017-0209

• 化工过程与装备 • 上一篇    下一篇

倾斜折流栅式换热器壳程流体流动与传热特性

古新1, 秦晓柯1, 王永庆1, 张大波2, 刘敏珊1   

  1. 1. 郑州大学河南省过程传热与节能重点实验室, 河南 郑州 450002;
    2. 中国烟草总公司郑州烟草研究院, 河南 郑州 450001
  • 收稿日期:2017-02-13 修回日期:2017-03-01 出版日期:2017-10-05 发布日期:2017-10-05
  • 通讯作者: 张大波,工程师,研究方向为过程设备流体流动与强化传热.
  • 作者简介:古新(1978-),男,博士,副教授,主要从事新型高效节能换热设备的研究.
  • 基金资助:
    国家自然科学基金(21776263)及河南省高等学校重点科研项目(18A470001)。

Research on fluid flow and heat transfer characteristics in shell side of inclined shutter baffle heat exchanger

GU Xin1, QIN Xiaoke1, WANG Yongqing1, ZHANG Dabo2, LIU Minshan1   

  1. 1. Key Laboratory of Process Heat Transfer and Energy Saving of Henan Province, Zhengzhou University, Zhengzhou 450002, Henan, China;
    2. Zhengzhou Tobacco Research Institute of CNTC, Zhengzhou 450001, Henan, China
  • Received:2017-02-13 Revised:2017-03-01 Online:2017-10-05 Published:2017-10-05

摘要: 针对斜向流换热器壳程流体流动的特点,提出一种倾斜折流栅式换热器。采用CFD软件Fluent对常规斜向流换热器和倾斜折流栅式换热器进行数值研究,分析了折流栅的装配方式和倾斜角度对倾斜折流栅式换热器壳侧流体流动和传热性能的影响。结果表明:与常规斜向流换热器相比,栅片同向装配时,倾斜折流栅式换热器壳程传热系数和综合性能分别增加6.18%~6.47%和3.22%~3.59%;栅片同向装配,折流栅倾斜角为70°时,换热器壳程传热系数和综合性能均达到最大,且壳程压降较小。与倾斜角为60°的倾斜折流栅式换热器相比,倾斜角为70°的倾斜折流栅式换热器壳程传热系数和综合性能分别增加2.84%~2.93%和7.07%~7.19%,且壳程压降降低11.26%~11.52%。所得结论为改进斜向流换热器折流栅的结构和强化传热提供理论与工程应用依据。

关键词: 流动, 传热, 数值模拟, 倾斜折流栅, 装配方式, 倾斜角度

Abstract: Based on the fluid flow characteristics of the shell-side of the sideling flow heat exchanger,a sideling flow heat exchanger with inclined shutter baffles was proposed. The numerical study of the conventional and inclined shutter baffles sideling flow heat exchangers was carried out with Fluent,a kind of CFD software,and the impacts of the modes the shutter baffle assembled and inclination angle on the fluid flow and heat transfer of sideling flow heat exchanger with inclined shutter baffles was analyzed. The results showed that the heat transfer coefficient and comprehensive performance of the inclined shutter baffle heat exchangers increase by 6.18%-6.47% and 3.22%-3.59% respectively,compared with the conventional sideling flow heat exchanger when the shutter baffles and strips were assembled concurrently. When the shutter baffles and strips were assembled concurrently,both heat transfer coefficient and comprehensive performance of the inclined shutter baffle heat exchangers with inclination angle of 70° reach the highest value with a relatively low shell side pressure drop. Compared with the heat exchanger with inclination angle of 60°,the heat transfer coefficient and comprehensive performance of the one with inclination angle of 70°increase by 2.84%-2.93% and 7.07%-7.19% respectively,and the shell-sided pressure drop decreases by 11.26%-11.52%. The results provide the theoretical and engineering application bases for the structure improvement and heat transfer enhancement of the sideling flow heat exchanger.

Key words: flow, heat transfer, numerical simulation, inclined shutter baffle, assembly mode, inclination angle

中图分类号: 

京ICP备12046843号-2;京公网安备 11010102001994号
版权所有 © 《化工进展》编辑部
地址:北京市东城区青年湖南街13号 邮编:100011
电子信箱:hgjz@cip.com.cn
本系统由北京玛格泰克科技发展有限公司设计开发 技术支持:support@magtech.com.cn