倾斜折流栅式换热器壳程流体流动与传热特性

doi:10.16085/j.issn.1000-6613.2017-0209

化工进展 ›› 2017, Vol. 36 ›› Issue (10): 3584-3589.DOI: 10.16085/j.issn.1000-6613.2017-0209

倾斜折流栅式换热器壳程流体流动与传热特性

古新¹, 秦晓柯¹, 王永庆¹, 张大波², 刘敏珊¹

1. 郑州大学河南省过程传热与节能重点实验室, 河南郑州 450002;
2. 中国烟草总公司郑州烟草研究院, 河南郑州 450001

收稿日期:2017-02-13 修回日期:2017-03-01 出版日期:2017-10-05 发布日期:2017-10-05
通讯作者: 张大波,工程师,研究方向为过程设备流体流动与强化传热.
作者简介:古新(1978-),男,博士,副教授,主要从事新型高效节能换热设备的研究.
基金资助:
国家自然科学基金（21776263）及河南省高等学校重点科研项目（18A470001）。

Research on fluid flow and heat transfer characteristics in shell side of inclined shutter baffle heat exchanger

GU Xin¹, QIN Xiaoke¹, WANG Yongqing¹, ZHANG Dabo², LIU Minshan¹

1. Key Laboratory of Process Heat Transfer and Energy Saving of Henan Province, Zhengzhou University, Zhengzhou 450002, Henan, China;
2. Zhengzhou Tobacco Research Institute of CNTC, Zhengzhou 450001, Henan, China

Received:2017-02-13 Revised:2017-03-01 Online:2017-10-05 Published:2017-10-05

摘要/Abstract

摘要： 针对斜向流换热器壳程流体流动的特点，提出一种倾斜折流栅式换热器。采用CFD软件Fluent对常规斜向流换热器和倾斜折流栅式换热器进行数值研究，分析了折流栅的装配方式和倾斜角度对倾斜折流栅式换热器壳侧流体流动和传热性能的影响。结果表明：与常规斜向流换热器相比，栅片同向装配时，倾斜折流栅式换热器壳程传热系数和综合性能分别增加6.18%～6.47%和3.22%～3.59%；栅片同向装配，折流栅倾斜角为70°时，换热器壳程传热系数和综合性能均达到最大，且壳程压降较小。与倾斜角为60°的倾斜折流栅式换热器相比，倾斜角为70°的倾斜折流栅式换热器壳程传热系数和综合性能分别增加2.84%～2.93%和7.07%～7.19%，且壳程压降降低11.26%～11.52%。所得结论为改进斜向流换热器折流栅的结构和强化传热提供理论与工程应用依据。

关键词: 流动, 传热, 数值模拟, 倾斜折流栅, 装配方式, 倾斜角度

Abstract: Based on the fluid flow characteristics of the shell-side of the sideling flow heat exchanger,a sideling flow heat exchanger with inclined shutter baffles was proposed. The numerical study of the conventional and inclined shutter baffles sideling flow heat exchangers was carried out with Fluent,a kind of CFD software,and the impacts of the modes the shutter baffle assembled and inclination angle on the fluid flow and heat transfer of sideling flow heat exchanger with inclined shutter baffles was analyzed. The results showed that the heat transfer coefficient and comprehensive performance of the inclined shutter baffle heat exchangers increase by 6.18%-6.47% and 3.22%-3.59% respectively,compared with the conventional sideling flow heat exchanger when the shutter baffles and strips were assembled concurrently. When the shutter baffles and strips were assembled concurrently,both heat transfer coefficient and comprehensive performance of the inclined shutter baffle heat exchangers with inclination angle of 70° reach the highest value with a relatively low shell side pressure drop. Compared with the heat exchanger with inclination angle of 60°,the heat transfer coefficient and comprehensive performance of the one with inclination angle of 70°increase by 2.84%-2.93% and 7.07%-7.19% respectively,and the shell-sided pressure drop decreases by 11.26%-11.52%. The results provide the theoretical and engineering application bases for the structure improvement and heat transfer enhancement of the sideling flow heat exchanger.

Key words: flow, heat transfer, numerical simulation, inclined shutter baffle, assembly mode, inclination angle

中图分类号:

TK124

古新, 秦晓柯, 王永庆, 张大波, 刘敏珊. 倾斜折流栅式换热器壳程流体流动与传热特性[J]. 化工进展, 2017, 36(10): 3584-3589.

GU Xin, QIN Xiaoke, WANG Yongqing, ZHANG Dabo, LIU Minshan. Research on fluid flow and heat transfer characteristics in shell side of inclined shutter baffle heat exchanger[J]. Chemical Industry and Engineering Progress, 2017, 36(10): 3584-3589.

参考文献

[1] 董其伍,张垚.换热器[M].北京:化学工业出版社,2009.DONG Q W,ZHANG Y.Heat exchanger[M].Beijing:Chemical Industry Press,2009.
[2] HOUKUAN T,LAPMOU T,SIKCHUNG T,et al.New optimization method,the algorithms of changes,for heat exchanger design[J].Chinese Journal of Mechanical Engineering,2012,25(1):55-62.
[3] 古新,王珂,刘冰,等.三角形布管帘式折流片换热器传热和流阻性能研究[J].工程热物理学报,2013(7):1327-1330.GU X,WANG K,LIU B,et al.Research on heat transfer and flow resistance performance of shutter baffle heat exchanger with triangle tube layout in shell side[J].Journal of Engineering Thermophysics,2013(7):1327-1330.
[4] XIAO X M,ZHANG L H,LI X G,et al.Numerical investigation of helical baffles heat exchanger with different Prandtl number fluids[J].International Journal of Heat and Mass Transfer,2013,63(15):434-444.
[5] 徐烨琨,刘成,李永辉.折流杆换热器的研究方法进展[J].化工进展,2014,33(7):1671-1676.XU Y K,LIU C,LI Y H.Progress of rod baffle heat exchanger[J].Chemical Industry and Engineering Progress,2014,33(7):1671-1676.
[6] 古新,董其伍,刘敏珊,等.帘式折流片换热器强化传热数值研究[J].高校化学工程学报,2010,24(2):340-345.GU X,DONG Q W,LIU M S,et al.Numerical research on heat transfer enhancement of shutter baffle heat exchanger[J].Journal of Chemical Engineering of Chinese Universities,2010,24(2):340-345.
[7] 刘冰.帘式折流片换热器壳程结构优化[D].郑州:郑州大学,2012.LIU B.Structure optimum for shutter baffle heat exchanger[D].Zhengzhou:Zhengzhou University,2012.
[8] 古新,王珂,董其伍,等.斜向流换热器壳程流场均匀化研究[J].工程热物理学报,2012,33(7):1237-1239.GU X,WANG K,DONG Q W,et al.Research on flow field homogenization in shell side of sidelling flow heat exchanger[J].Journal of Engineering Thermophysics,2012,33(7):1237-1239.
[9] WANG Y Q,GU X,JIN Z L,et al.Characteristics of heat transfer for tube banks in crossflow and its relation with that in shell-and-tube heat exchangers[J].International Journal of Heat and Mass Transfer,2016,93:584-594.
[10] 谭祥辉,孙赫,张立振,等.扭曲椭圆管换热的壳程强化传热特性[J].化工学报,2012,63(3):713-720.TAN X H,SUN H,ZHANG L Z,et al.Shell side heat transfer enhancement in twisted elliptical tube heat exchanger[J].CIESC Journal,2012,63(3):713-720.

[1]	肖辉, 张显均, 兰治科, 王苏豪, 王盛. 液态金属绕流管束流动传热进展[J]. 化工进展, 2023, 42(S1): 10-20.
[2]	王太, 苏硕, 李晟瑞, 马小龙, 刘春涛. 交流电场中贴壁气泡的动力学行为[J]. 化工进展, 2023, 42(S1): 133-141.
[3]	赵晨, 苗天泽, 张朝阳, 洪芳军, 汪大海. 负压状态窄缝通道乙二醇水溶液传热特性[J]. 化工进展, 2023, 42(S1): 148-157.
[4]	陈匡胤, 李蕊兰, 童杨, 沈建华. 质子交换膜燃料电池气体扩散层结构与设计研究进展[J]. 化工进展, 2023, 42(S1): 246-259.
[5]	郭强, 赵文凯, 肖永厚. 增强流体扰动强化变压吸附甲硫醚/氮气分离的数值模拟[J]. 化工进展, 2023, 42(S1): 64-72.
[6]	邵博识, 谭宏博. 锯齿波纹板对挥发性有机物低温脱除过程强化模拟分析[J]. 化工进展, 2023, 42(S1): 84-93.
[7]	陈林, 徐培渊, 张晓慧, 陈杰, 徐振军, 陈嘉祥, 密晓光, 冯永昌, 梅德清. 液化天然气绕管式换热器壳侧混合工质流动及传热特性[J]. 化工进展, 2023, 42(9): 4496-4503.
[8]	刘炫麟, 王驿凯, 戴苏洲, 殷勇高. 热泵中氨基甲酸铵分解反应特性及反应器结构优化[J]. 化工进展, 2023, 42(9): 4522-4530.
[9]	罗成, 范晓勇, 朱永红, 田丰, 崔楼伟, 杜崇鹏, 王飞利, 李冬, 郑化安. 中低温煤焦油加氢反应器不同分配器中液体分布的CFD模拟[J]. 化工进展, 2023, 42(9): 4538-4549.
[10]	赵曦, 马浩然, 李平, 黄爱玲. 错位碰撞型微混合器混合性能的模拟分析与优化设计[J]. 化工进展, 2023, 42(9): 4559-4572.
[11]	卜治丞, 焦波, 林海花, 孙洪源. 脉动热管计算流体力学模型与研究进展[J]. 化工进展, 2023, 42(8): 4167-4181.
[12]	汪健生, 张辉鹏, 刘雪玲, 傅煜郭, 朱剑啸. 多孔介质结构对储层内流动和换热特性的影响[J]. 化工进展, 2023, 42(8): 4212-4220.
[13]	王云刚, 焦健, 邓世丰, 赵钦新, 邵怀爽. 冷凝换热与协同脱硫性能实验分析[J]. 化工进展, 2023, 42(8): 4230-4237.
[14]	叶振东, 刘涵, 吕静, 张亚宁, 刘洪芝. 基于钙镁二元盐的热化学储能反应器的性能优化[J]. 化工进展, 2023, 42(8): 4307-4314.
[15]	俞俊楠, 俞建峰, 程洋, 齐一搏, 化春键, 蒋毅. 基于深度学习的变宽度浓度梯度芯片性能预测[J]. 化工进展, 2023, 42(7): 3383-3393.

倾斜折流栅式换热器壳程流体流动与传热特性

Research on fluid flow and heat transfer characteristics in shell side of inclined shutter baffle heat exchanger

PDF (PC)

可视化

被引次数

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价