化工进展 ›› 2023, Vol. 42 ›› Issue (5): 2647-2654.DOI: 10.16085/j.issn.1000-6613.2022-1371

• 精细化工 • 上一篇    下一篇

压裂用耐温乳液稠化剂的制备及性能

周亚峰(), 杨江(), 马诚, 刘海玲   

  1. 辽宁石油化工大学石油化工学院,辽宁 抚顺 113001
  • 收稿日期:2022-07-21 修回日期:2022-08-18 出版日期:2023-05-10 发布日期:2023-06-02
  • 通讯作者: 杨江
  • 作者简介:周亚峰(1994—),男,硕士研究生,研究方向为油田化学。E-mail:740209987@qq.com
  • 基金资助:
    辽宁省“兴辽英才”计划(SLYC1902053)

Preparation and properties of heat resistant emulsion thickener for fracturing

ZHOU Yafeng(), YANG Jiang(), MA Cheng, LIU Hailing   

  1. College of Petrochemical Engineering, Liaoning Petrochemical University, Fushun 113001, Liaoning, China
  • Received:2022-07-21 Revised:2022-08-18 Online:2023-05-10 Published:2023-06-02
  • Contact: YANG Jiang

摘要:

为发展耐温疏水聚合物压裂液体系,本文在丙烯酰胺、丙烯酸、2-丙烯酰胺-2-甲基丙磺酸(AMPS)中引入了疏水单体甲基丙烯酸十八烷基酯来提高稠化剂的耐温性,合成了聚合物稠化剂PAS。实验结果表明,制备改性聚合物的条件为:单体占总质量的30%,乳化剂占油相的10%,亲水亲油平衡值(HLB)为6,引发剂占单体质量的0.2%,油水相比为1∶2。其黏均分子量为450×104g/mol。测试了该聚合物1.5%的浓度在120℃、170s-1下剪切1.5h后黏度保持在80mPa·s,具有较好的耐温性,并具有剪切回复性能;其粒径分布为500~1200nm;在破胶剂过硫酸钾的用量为0.03%时,在90℃下,其黏度可以下降到5mPa·s,完成破胶。

关键词: 压裂液, 耐温性, 稠化剂, 耐剪切性, 破胶性

Abstract:

In order to develop the heat-resistant hydrophobic polymer fracturing fluid system, in this paper, hydrophobic monomer octadecyl methacrylate was introduced into acrylamide acrylic acid AMPS to improve the temperature resistance of thickeners, and the polymer thickeners PAS was synthesized. The experimental results showed that the preparation conditions of modified polymer were as follows: monomer accounted for 30% of the total mass, emulsifier accounted for 10% of the oil phase, hydrophilic lipophilic balance (HLB) was 6, initiator accounted for 0.2% of the total mass of monomer, and oil water ratio was 1∶2. Its viscosity-average molecular weight was 450×104g/mol. The viscosity of the polymer at 1.5% concentration remained at 80mPa·s after shearing for 1.5h at 120℃ and 170s-1. The polymer had good temperature resistance and shear recovery performance. Its particle size distribution was 500—1200nm. When the amount of potassium persulfate as gel breaker was 0.03%, the viscosity could be reduced to 5mPa·s at 90℃, reaching glue breaking.

Key words: fracturing fluid, temperature resistance, thickener, shear resistance, gel-breaking property

中图分类号: 

京ICP备12046843号-2;京公网安备 11010102001994号
版权所有 © 《化工进展》编辑部
地址:北京市东城区青年湖南街13号 邮编:100011
电子信箱:hgjz@cip.com.cn
本系统由北京玛格泰克科技发展有限公司设计开发 技术支持:support@magtech.com.cn