气泡在颗粒床层表面的生成脱离行为

doi:10.16085/j.issn.1000-6613.2020-0671

摘要/Abstract

摘要：

试验研究了气泡在颗粒床层表面的生成脱离过程及其行为特性，利用高速摄像技术揭示了进气管管径、颗粒床层高度、颗粒粒径等因素对气泡脱离直径及其生成周期的影响规律，对比分析了颗粒床层表面和进气管管口的气泡生成脱离行为差异。研究结果表明：在1500～3000μm粒径范围的床层表面所生成气泡的初始形态相对更扁小，气泡也更快向扁平状演变；颗粒粒径的增大使得进气流量对气泡形态的影响减弱；管径和颗粒床层高度的增大可以有效促进气泡脱离直径的增长，但延缓了气泡的生成脱离，增加了气泡的生成周期；颗粒粒径对气泡生成周期的影响随着进气流量的增大而逐渐减弱；气泡在颗粒床层表面和管口的生成脱离行为存在显著差异，相比之下，150～300μm粒径范围的颗粒床层对气泡的生成脱离具有更明显的阻碍作用，其表面所生成气泡的脱离直径和生成周期相对较大。

关键词: 气泡, 多相流, 鼓泡反应器, 脱离直径, 生成周期

Abstract:

The bubble formation and detachment behaviors on the surface layer of packed particles were studied experimentally. The effects of nozzle diameter, packed bed height and particle size on the bubble detachment diameter and the formation period were revealed by using the high-speed camera technology. The differences of bubble formation and detachment behaviors on the surface layer of packed bed and the nozzle were analyzed. The results showed that the initial shape of the bubble generated on the surface of packed bed with the particle size in the range of 1500—3000μm was relatively flat and small, and the evolution of bubble to flat shape was faster. The effect of intake flow rate on the bubble shape was weakened with the increase of particle size. And the increase of nozzle diameter and packed bed height could effectively promote the growth of bubble detachment diameter, but delayed the formation and detachment of bubble and increased the bubble formation period. The effect of particle size on the bubble formation period diminished gradually with the increase of intake flow rate. There was a significant difference between the bubble formation and detachment behaviors on the surface of packed bed and the nozzle. In contrast, the packed bed with the particle size in the range of 150—300μm had a more obvious hindering effect on the formation and detachment of bubble, and the detachment diameter and the formation period of bubble were relatively large.

Key words: bubble, multiphase flow, bubble column reactor, detachment diameter, formation period

中图分类号:

O359.1

魏楠, 吴晅, 薄宇轩, 刘鹏, 马骏. 气泡在颗粒床层表面的生成脱离行为[J]. 化工进展, 2021, 40(2): 678-687.

Nan WEI, Xuan WU, Yuxuan BO, Peng LIU, Jun MA. Bubble formation and detachment behaviors on surface layer of packed particles[J]. Chemical Industry and Engineering Progress, 2021, 40(2): 678-687.

图/表 11

图1 试验装置1—计算机系统；2—数据传输线；3—高速摄像机；4—空压机；5—阀门；6—玻璃转子流量计；7—橡胶管；8—橡胶塞；9—进气管；10—液池；11—柔光布；12—LED光源

图2 气泡生成示意图

表1 进气管规格

编号	D_o/mm	D_i/mm
一号管	1.5	1.35
二号管	2.5	2.35
三号管	4.0	3.85
四号管	7.0	6.75
五号管	9.0	8.75

图3 气泡信息提取图a—关键帧图片中气泡长轴长；b—关键帧图片中气泡短轴长；do—关键帧图片中进气管外径

图4 不同颗粒粒径和进气流量下气泡生成脱离过程

图5 进气管管径对气泡脱离直径的影响规律

图6 进气管管径对气泡生成周期的影响规律

图7 颗粒床层高度对气泡脱离直径的影响规律

图8 颗粒床层高度对气泡生成周期的影响规律

图9 颗粒粒径对气泡生成脱离行为的影响规律

图10 气泡在管口和颗粒床层表面的生成脱离行为对比

参考文献 33

1	CHAO Cong, XU Xu, KWELLE S O, et al. Significance of gas-liquid interfaces for two-phase flows in micro-channels[J]. Chemical Engineering Science, 2018, 192: 114-125.
2	YAO Chao, LI Huixiong, XUE Yuqing, et al. Investigation on the frictional pressure drop of gas liquid two-phase flows in vertical downward tubes[J]. International Communications in Heat and Mass Transfer, 2018, 91: 138-149.
3	ALIYU M A, BABA Y D, LAO L Y, et al. Interfacial friction in upward annular gas-liquid two-phase flow in pipes[J]. Experimental Thermal and Fluid Science, 2017, 84: 90-109.
4	刘春, 王聪聪, 陈晓轩, 等. 微气泡曝气生物膜反应器处理低C/N比废水脱氮过程[J]. 环境科学, 2019, 40(2): 754-760.
	LIU Chun, WANG Congcong, CHEN Xiaoxuan, et al. Biological nitrogen removal process in a microbubble-aerated biofilm reactor treating low C /N wastewater[J]. Environment Science, 2019, 40(2): 754-760.
5	詹俊伟, 陈卓, 詹旭, 等. 微气泡曝气条件下仿生水草生物接触氧化池对污水的处理效果[J]. 环境污染与防治, 2018, 40(2): 217-221.
	ZHAN Junwei, CHEN Zhuo, ZHAN Xu, et al. Studies on the performance of bionic aquatic filler biological contact oxidation tank for wastewater treatment based on microbubble aeration[J]. Environmental Pollution & Control, 2018, 40(2): 217-221.
6	苏延琪. 浮选脱墨中提高纤维得率的措施[J]. 国外技术, 2010, 31(16): 78-81.
	SU Yanqi. Measures on improving yield of flotation deinking[J]. Oversea Technology, 2010, 31(16): 78-81.
7	王帅, 李攀, 于水利. 微米气泡特性及其在环境领域的应用[J]. 中国给水排水, 2013, 29(20): 22-25.
	WANG Shuai, LI Pan, YU Shuili. Characteristics of microbubbles and their applications in environmental management[J]. China Water and Wastewater, 2013, 29(20): 22-25.
8	HUBER M, DOBESCH D, KUNZ P, et al. Influence of orifice type and wetting properties on bubble formation at bubble column reactors[J]. Chemical Engineering Science, 2016, 152: 151-162.
9	李孟, 李向阳, 王宏智, 等. 鼓泡塔气液两相流不同曳力模型的数值模拟[J]. 过程工程学报, 2015, 15(2): 181-189.
	LI Meng, LI Xiangyang, WANG Hongzhi, et al. Numerical simulation of different traction force models for gas-liquid two-phase flow in bubble tower[J]. The Chinese Journal of Process Engineering, 2015, 15(2): 181-189.
10	ZIEGENHEIN T, LUCAS D. Observations on bubble shapes in bubble columns under different flow conditions[J]. Experimental Thermal and Fluid Science, 2017, 85: 248-256.
11	KHODABANDEHLOU R, ASKARIPOUR H, DEHKORDI A M. Numerical investigation of gas bubble behavior in tapered fluidized beds[J]. Particuology, 2018, 38: 152-164.
12	张航, 吕友军. 超临界水循环流化床两相流动特性的数值模拟[J]. 工程热物理学报, 2018, 39(1): 127-132.
	ZHANG Hang, Youjun LYU. Numerical simulation on two-phase flow characteristics in the supercritical water circulating fluidized bed riser[J]. Journal of Engineering Thermophysics, 2018, 39(1): 127-132.
13	LI Xiangnan, LIU Mingyan, MA Yongli, et al. Experiments and meso-scale modeling of phase holdups and bubble behavior in gas-liquid- solid mini-fluidized beds[J]. Chemical Engineering Science, 2018, 192: 725-738.
14	陈阿强, 黄青山, 耿淑君, 等. 喷射反应器内气液两相流体动力学特征[J]. 化工进展, 2018, 37(4): 1257-1266.
	CHEN Aqiang, HUANG Qingshan, GENG Shujun, et al. Hydrodynamic characteristics of gas-liquid two phase flow in jet reactors[J]. Chemical Industry and Engineering Progress, 2018, 37(4): 1257-1266.
15	DIETRICH N, MAYOUFI N, PONCIN S, et al. Bubble formation at an orifice: a multiscale investigation[J]. Chemical Engineering Science, 2013, 92(14): 118-125.
16	ZHANG Jian, YU Yong, QU Chen, et al. Experimental study and numerical simulation of periodic bubble formation at submerged micron-sized nozzles with constant gas flow rate[J]. Chemical Engineering Science, 2017, 168: 1-10.
17	QU Chen, YU Yong, ZHANG Jian, et al. Experimental study of bubbling regimes on submerged micro-orifices[J]. International Journal of Heat and Mass Transfer, 2017, 111: 17-28.
18	刘子炜, 戴诗逸, 段聪, 等. 台阶式单微通道内气泡生成动力学[J]. 化工学报, 2020, 71(2): 552-565.
	LIU Ziwei, DAI Shiyi, DUAN Cong, et al. Dynamics of bubble formation in single step-type microchannel[J]. CIESC Journal, 2020, 71(2): 552-565.
19	TSUGE H, TEZUKA Y, MITSUDANI M, et al. Bubble formation mechanism from downward nozzle-effect of nozzle shape and operating parameters[J]. Chemical Engineering Science, 2006, 61(10): 3290-3298.
20	田震, 成有为, 王丽军, 等. 温度与压力对单孔气泡形成过程的影响[J]. 化工学报, 2019, 70(9): 3337-3345.
	TIAN Zhen, CHENG Youwei, WANG Lijun, et al. Effect of tempeture and pressure on formation process of single-hole bubbles[J]. CIESC Journal, 2019, 70(9): 3337-3345.
21	SUBRAT D, YOS S, GEOFFREY B, et al. Principal characteristics of a bubble formation on a horizontal downward facing surface[J]. Colloids and Surfaces A: Physicochemical and Engineering Aspects, 2012, 411: 94-104.
22	李少白, 徐双, 李润东, 等. 剪切变稀流体中的单气泡生成行为[J]. 化学工程, 2016, 44(3): 46-49.
	LI Shaobai, XU Shuang, LI Rundong, et al. Formation behavior of single bubble in shear-thinning fluids[J]. Chemical Engineering, 2016, 44(3): 46-49.
23	张健, 于勇, 胡俊. 低气流量时水下微米级针管气泡生成试验研究[J]. 工程热物理学报, 2018, 39(3): 561-566.
	ZHANG Jian, YU Yong, HU Jun. Experimental study of bubble formation from a submerged micron nozzle[J]. Journal of Engineering Thermophysics, 2018, 39(3): 561-566.
24	张翀, 付涛涛, 姜韶堃, 等. 聚焦十字型微通道内高黏流体中气泡生成动力学[J]. 化工学报, 2018, 69(2): 650-654.
	ZHANG Chong, FU Taotao, JIANG Shaokun, et al. Bubble forming dynamics of highly viscous fluids in microfluidic flow-focusing cross channel device[J]. CIESC Journal, 2018, 69(2): 650-654.
25	YANG G Q, LUO X, LAU R, et al. Bubble formation in high pressure liquid-solid suspensions with plenum pressure fluctuation[J]. AIChE Journal, 2000, 46: 2162-2172.
26	LI Y, YANG G Q, ZHANG J P, et al. Numercial studies of bubble formation dynamics in gas-liquid-solid fluidization at high pressures[J]. Powder Technology, 2001, 116(2/3): 246-260.
27	李彦鹏, 张乾隆. 液固悬浮液中气泡生成的数值模拟[J]. 水动力学研究与进展, 2007, 22(4): 457-463.
	LI Yanpeng, ZHANG Qianlong. Numercial simulation of bubble formation in liguid-solid suspensions[J]. Journal of Hydrodynamics (Ser. A), 2007, 22(4): 457-463.
28	XU Yonggui, LIU Mingyan, TANG Can. Three-dimensional CFD-VOF-DPM simulations of effects of low-holdup particles on single-nozzle bubbling behavior in gas-liquid-solid systems[J]. Chemical Engineering Journal, 2013, 222: 292-306.
29	LIN Yongming. The dynamic equation for a spherical bubble in uniform sized solid particle-liquid homogeneous suspension[J]. Journal of Hydrodynamics (Ser. B), 1997, 9(4): 9-18.
30	MA Keying, LIU Mingyan, CHEN Shaoqi, et al. The axial and radial phase holdup distribution of bubble-induced three-phase inverse fluidized bed[J]. Chemical Engineering Science, 2020, 219(29): 115586.
31	高光才, 文联奎, 郑远扬. 喷射诱导气浮处理含油污水性能研究[J]. 石油学报, 2001, 22(4): 108-113.
	GAO Guangcai, WEN Liankui, ZHENG Yuanyang. A study on performances of nozzle gas-induced floatation[J]. Acta Petrolei Sinica, 2001, 22(4): 108-113.
32	ROSA A F, RUBIO J. On the role of nanobubbles in particle-bubble adhesion for the flotation of quartz and apatitic minerals[J]. Minerals Engineering, 2018, 127: 178-184.
33	吴晅, 李晓瑞, 马骏, 等. 不同管口浸没方式下气泡生成行为特性[J]. 化工学报, 2019, 70(3): 901-912.
	WU Xuan, LI Xiaorui, MA Jun, et al. Behavior characteristics of bubble formation under various nozzle immersion modes[J]. CIESC Journal, 2019, 70(3): 901-912.

[1]	杨寒月, 孔令真, 陈家庆, 孙欢, 宋家恺, 王思诚, 孔标. 微气泡型下向流管式气液接触器脱碳性能[J]. 化工进展, 2023, 42(S1): 197-204.
[2]	黄益平, 李婷, 郑龙云, 戚傲, 陈政霖, 史天昊, 张新宇, 郭凯, 胡猛, 倪泽雨, 刘辉, 夏苗, 主凯, 刘春江. 三级环流反应器中气液流动与传质规律[J]. 化工进展, 2023, 42(S1): 175-188.
[3]	盛维武, 程永攀, 陈强, 李小婷, 魏嘉, 李琳鸽, 陈险峰. 微气泡和微液滴双强化脱硫反应器操作分析[J]. 化工进展, 2023, 42(S1): 142-147.
[4]	王太, 苏硕, 李晟瑞, 马小龙, 刘春涛. 交流电场中贴壁气泡的动力学行为[J]. 化工进展, 2023, 42(S1): 133-141.
[5]	王云飞, 秦蕊, 郑利军, 李焱, 李清平. 旋转填充床CFD模拟研究进展[J]. 化工进展, 2023, 42(S1): 1-9.
[6]	奚永兰, 王成成, 叶小梅, 刘洋, 贾昭炎, 曹春晖, 韩挺, 张应鹏, 田雨. 微纳米气泡在厌氧消化中的应用研究进展[J]. 化工进展, 2023, 42(8): 4414-4423.
[7]	陈蔚阳, 宋欣, 殷亚然, 张先明, 朱春英, 付涛涛, 马友光. 矩形微通道内液相黏度对气泡界面的作用机制[J]. 化工进展, 2023, 42(7): 3468-3477.
[8]	章凯, 金捍宇, 刘思宇, 王帅. 鼓泡流态化气泡间相互作用下相间传质过程的模拟[J]. 化工进展, 2023, 42(6): 2828-2835.
[9]	田启凯, 郑海萍, 张少斌, 张静, 余子夷. 混合增强的微流控通道进展[J]. 化工进展, 2023, 42(4): 1677-1687.
[10]	乔元, 仇畅, 钱锦远, 干瑞彬, 徐春明, 金志江. 笼式调节阀的冲蚀磨损与空蚀[J]. 化工进展, 2023, 42(10): 5111-5120.
[11]	陈磊, 田科, 曾力, 张俊丰, 黄妍, 何峰. 焦化脱硫废杂盐资源化新技术[J]. 化工进展, 2023, 42(1): 480-487.
[12]	陈二军, 张玉玲, 路少磊, 段海洋, 靳文章. 空气纳米气泡的稳定性及理化特性[J]. 化工进展, 2022, 41(9): 4673-4681.
[13]	张伟, 王军锋, 苏巧玲, 吴天一. 针-环电极配置下电场对气泡分散特性的影响[J]. 化工进展, 2022, 41(6): 2931-2938.
[14]	张春超, 潘艳秋, 杜宇杰, 高石磊, 俞路. 喷雾冷却中液滴撞击带气泡液膜的数值模拟[J]. 化工进展, 2022, 41(4): 1735-1741.
[15]	郑鹏, 李蔚玲, 郭亚飞, 孙健, 王瑞林, 赵传文. 鼓泡床中电石渣加速碳酸化分析与响应面优化[J]. 化工进展, 2022, 41(3): 1528-1538.