三叶孔板强化换热性能及机理分析

doi:10.16085/j.issn.1000-6613.2017.02.009

化工进展 ›› 2017, Vol. 36 ›› Issue (02): 465-472.DOI: 10.16085/j.issn.1000-6613.2017.02.009

三叶孔板强化换热性能及机理分析

魏志国, 李华峰, 柯汉兵, 张克龙

武汉第二船舶设计研究所热能动力技术重点实验室, 湖北武汉 430205

收稿日期:2016-06-29 修回日期:2016-08-03 出版日期:2017-02-05 发布日期:2017-02-05
通讯作者: 魏志国(1984-),男,硕士,工程师。E-mail:za2002@163.com。
作者简介:魏志国(1984-),男,硕士,工程师。E-mail:za2002@163.com。
基金资助:
国家自然科学基金（51406138）及湖北省自然科学基金（2015CFB521）项目。

Analysis on performance and mechanism of heat transfer enhancement of trifoil-hole baffle

WEI Zhiguo, LI Huafeng, KE Hanbing, ZHANG Kelong

Science and Technology on Thermal Energy and Power Laboratory, Wuhan 2nd Ship Design and Research Institute, Wuhan 430064, Hubei, China

Received:2016-06-29 Revised:2016-08-03 Online:2017-02-05 Published:2017-02-05

摘要/Abstract

摘要： 三叶孔板是以纵向流形式强化管壳式换热器性能的一种典型支撑板结构，具有附加阻力小和能够降低管束流激振动等诸多优势。为了分析三叶孔板对管壳式换热器壳程传热性能的强化效果和机理，本文依据周期性和对称性特征构建了不同孔高的换热器单元流道模型，采用重整化群k-ε湍流模型和SIMPLE耦合算法分析其壳程流场分布特征并评估其综合换热性能。结果表明，三叶孔板换热器Nu数和阻力系数较无孔板管壳式换热器均有所增加，相对Nu数（Nu/Nu₀）和相对阻力系数（f/f₀）随孔高H增大而减小，性能评价指标（performance evaluation indicators，PEC）随孔高H增大而增大。与无孔板管壳式换热器相比，三叶孔板换热器壳程纵向各处场协同角β较小而纵向涡强度Ω_x较大，因此场协同性的改善和纵向涡强度的提高是三叶孔板强化换热的原因。

关键词: 三叶孔板, 强化换热, 综合性能, 机理分析

Abstract: Trifoil-hole baffle is a typical support plate which can improve heat transfer performance of tube and shell heat exchanger in the form of longitudinal flow,with many advantages such as smaller resistance and the ability of flow induced vibration weakening. In order to analyze the heat transfer enhancement effect and mechanism of trifoil-hole baffle on the shell side of tube and shell heat exchanger,a series of unit channel models for trifoil-hole baffle with different hole height H was built according to the periodical and symmetrical characteristics. The renormalization group k-epsilon turbulence model and SIMPLE coupling algorithm were adopted for numerical simulation of shell side flow and comprehensive heat transfer performance evaluation. Results showed that Nusselt number Nu and resistance coefficient f of heat exchanger with trifoil-hole baffle are all larger than that without trifoil-hole baffle. Both the relative ratio of Nu/Nu₀ and f/f₀ decrease with H but the value of performance evaluation indicators(PEC)increases with H. Besides,the surface average of synergy angle β is lesser and longitudinal vortex magnitude Ωx is larger for heat exchanger with trifoil-hole baffle compared with that without trifoil-hole baffle,which illustrate the improvement of field synergy and intensification of longitudinal vortex all contribute to the heat transfer enhancement of trifoil-hole baffle.

Key words: trifoil-hole baffle, heat transfer enhancement, comprehensive performance, mechanism analysis

中图分类号:

TK124

魏志国, 李华峰, 柯汉兵, 张克龙. 三叶孔板强化换热性能及机理分析[J]. 化工进展, 2017, 36(02): 465-472.

WEI Zhiguo, LI Huafeng, KE Hanbing, ZHANG Kelong. Analysis on performance and mechanism of heat transfer enhancement of trifoil-hole baffle[J]. Chemical Industry and Engineering Progree, 2017, 36(02): 465-472.

参考文献

[1] 钱颂文. 换热器设计手册[M]. 北京:化学工业出版社,2002. QIAN S W. Heat exchanger design handbook[M]. Beijing:Chemical Industry Press,2002.
[2] 王秋旺,罗来勤,曾敏,等. 交错螺旋折流板管壳式换热器壳侧传热与阻力性能[J]. 化工学报,2005,56(4):598-601. WANG Q W,LUO L Q,ZENG M,et al. Shell-side heat transfer and pressure drop of shell-and-tube heat exchangers with overlap helical baffles[J]. CIESC Journal,2005,56(4):598-601.
[3] 汪淑奇,黄素逸. 纵流式换热器壳侧支撑方式的数值研究[J]. 化工学报,2007,58(5):1097-1103. WANG S Q,HUANG S Y. Numerical investigation on shell side support of longitudinal flow heat exchanger[J]. CIESC Journal,2007,58(5):1097-1103.
[4] 冯刚. 换热器管束流体诱导振动机理与防振研究进展[J]. 化工进展,2012,31(3):508-512. FENG G. Research progress in the flow induced vibration mechanism of tube bundles in heat exchangers and precautionary measures[J]. Chemical Industry and Engineering Progress,2012,31(3):508-512.
[5] 吴金星,魏新利,董其伍,等. 杆支撑换热器壳程的单元流道模型及流场分布[J]. 化工进展,2007,26(1):69-72. WU J X,WEI X L,DONG Q W,et al. Unit duct model and flow field distribution in shell side of rod baffle heat exchanger[J]. Chemical Industry and Engineering Progress,2007,26(1):69-72.
[6] 董其伍,白彩鹏,刘敏珊,等. 三叶孔板换热器壳程流体流动和传热研究[J]. 工程热物理学报,2013,34(1):115-117. DONG Q W,BAI C P,LIU M S,et al. Research on flow and heat transfer in shell-side of the trefoil-baffle support type heat exchanger[J]. Journal of Engineering Thermophysics,2013,34(1):115-117.
[7] 陶文铨. 数值传热学[M]. 2版. 西安:西安交通大学出版社,2006. TAO W Q. Heat exchanger design handbook[M]. 2nd ed. Xi'an:Xi'an Jiaotong University Press,2006.
[8] YAKHOT V,SMITH L M.The renormalization group,the ε-expansion and derivation of turbulence models[J]. Journal of Scientific Computing,1992,7(1):35-61.
[9] 弗兰克P. 英克鲁佩勒,大卫P. 德维特,狄奥多尔L. 伯格曼,等. 传热和传质基本原理[M]. 葛新石,叶宏,译. 6版. 北京:化学工业出版社,2007:303. INCROPERA F P,DEWITT D P,BERGMAN T L,et al. Fundamentals of heat and mass transfer[M]. GE X S,YE H,trans. 6th ed. Beijing:Chemical Industry Press,2007:303.
[10] 焦兰. 三叶孔整圆形支撑板换热器的实验及数值模拟研究[D]. 武汉:华中科技大学,2011. JIAO L. Experimental study and numerical simulation of heat exchanger with triporate full circular supporting structures[D]. Wuhan:Huazhong University of Science & Technology,2011.
[11] WEBB R L. Performance evaluation criteria for use of enhanced heat transfer surfaces in heat exchanger design[J]. International Journal of Heat and Mass Transfer,1981,24(4):715-726.
[12] GUO Z Y,LI D Y,WANG B X. A novel concept for convective heat transfer enhancement[J]. International Journal of Heat Mass Transfer,1998,41(14):2221-2225.
[13] TAO W Q,GUO Z Y,WANG B X. Field synergy principle for enhancing convective heat transfer——its extension and numerical verifications[J]. International Journal of Heat and Mass Transfer,2002,45(15):3849-3856.
[14] 王定标,王宏斌,梁珍祥. 扭曲三叶管传热与流阻性能的数值研究[J]. 化工学报,2012,63(7):2064-2069. WANG D B,WANG H B,LIANG Z X. Numerical research on heat transfer and flow resistance performance of twisted trifoliate tube[J]. CIESC Journal,2012,63(7):2064-2069.
[15] 何雅玲,陶文铨.强化单相对流换热的基本机制[J]. 机械工程学报,2009,45(3):27-38. HE Y L,TAO W Q. Fundamental mechanism of enhancing single-phase convective heat transfer[J]. Journal of Mechanical Engineering,2009,45(3):27-38.
[16] MARTIN F. Embedded vortices in internal flow:heat transfer and pressure loss enhancement[J]. International Journal of Heat and Fluid Flow,1995,16(5):376-388.
[17] 童秉纲,尹协远,朱克勤. 涡运动理论[M]. 合肥:中国科学技术大学出版社,1994. TONG B G,YIN X Y,ZHU K Q. Eddy motion theory[M]. Hefei:Press of University of Science and Technology of China,1994.

三叶孔板强化换热性能及机理分析

Analysis on performance and mechanism of heat transfer enhancement of trifoil-hole baffle

PDF (PC)

可视化

被引次数

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	王乐乐, 杨万荣, 姚燕, 刘涛, 何川, 刘逍, 苏胜, 孔凡海, 朱仓海, 向军. SCR脱硝催化剂掺废特性及性能影响[J]. 化工进展, 2023, 42(S1): 489-497.
[2]	田追, 张震, 卢嫚, 杨斌, 杨金辉, 周书葵, 魏柏, 李聪. 新型除氟吸附材料的研究进展[J]. 化工进展, 2022, 41(6): 3051-3062.
[3]	梅响, 姚元鹏, 吴慧英. 连通微通道内过冷流动沸腾传热强化机理分析[J]. 化工进展, 2022, 41(6): 2884-2892.
[4]	李艺凡, 王志鹏. 带有周期性扰流结构的微通道内流动与传热特性[J]. 化工进展, 2022, 41(6): 2893-2901.
[5]	林清宇, 王祝, 冯振飞, 凌彪, 陈镇. 扭带结构影响管内传热与熵产的研究进展[J]. 化工进展, 2022, 41(11): 5709-5721.
[6]	申宇, 潘振海, 吴慧英. 方肋微通道内流动沸腾的气泡动态与传热特性分析[J]. 化工进展, 2020, 39(7): 2548-2555.
[7]	李均星, 郭锦棠, 张弛, 李鹏鹏. 一种新型缓凝剂的制备及其在水泥基复合材料中的应用[J]. 化工进展, 2019, 38(06): 2953-2960.
[8]	徐志明, 熊骞, 王景涛, 韩志敏. 腰槽开孔矩形翼涡流发生器的传热和流阻特性[J]. 化工进展, 2017, 36(06): 2023-2030.
[9]	欧阳新萍, 舒涛, 刘冰翛. R410A、R404A、R407C在水平强化换热管外的凝结换热[J]. 化工进展, 2017, 36(02): 481-486.
[10]	王定标, 邓靜, 张灿灿, 张喜迎, 董桢, 谷帆江. 螺旋缠绕波节管传热与流动性能分析[J]. 化工进展, 2016, 35(07): 1994-2000.
[11]	胡丞, 高景山, 张英. 化学镀在换热表面强化滴状凝结、阻垢、耐蚀研究进展[J]. 化工进展, 2015, 34(s1): 10-17.
[12]	李惟毅, 梁娜, 孟金英, 贾向东, 李志会. 基液氨浓度对卡琳娜循环不同目标参数的影响[J]. 化工进展, 2015, 34(04): 957-964.
[13]	范国荣, 范魁元, 刘丕龙, 江乐新. 不同结构型式纵翅片管综合换热性能的数值模拟[J]. 化工进展, 2015, 34(04): 935-940,951.
[14]	朱凌云1，杨锦春2，周帼彦1，谭祥辉1，郭震1，朱辉1，郎红方2，朱冬生1. 三叶孔板换热器热力性能及其影响因素分析[J]. 化工进展, 2014, 33(12): 3183-3188.
[15]	冯刚. 换热器管束流体诱导振动机理与防振研究进展[J]. 化工进展, 2012, 31(03): 508-512.