Visualization study of reunion liquid atomization bubble size distribution characteristics

doi:10.16085/j.issn.1000-6613.2016.10.011

Abstract

Abstract: Reunion foam is an effective method for removal of fine particulate matter of PM_2.5. The particle sizes of the reunion liquid when atomize were studied to choose the suitable bubble size and spray conditions for the aggregation of PM_2.5 solution. The foam bubble size and aggregate amount of particulate matter were estimated according to the formulas. By CCD,the finely atomized liquid foam movement from nozzles was recorded. To calculate the atomization bubble size and distribution,MATLAB was used for the image processing. Results showed that the atomized foaming agent could promote the liquid to form bubbles and increase the diameter of the atomized particles. The bubble size of PAM reunion liquid was small,and the atomized particle density was big,the mainly particle size was less than 200μm,while the XTG bubble size was large,and the CMC bubble size was in between. The 0.2% CMC liquid gave the uniform bubble size,and larger number of particles. At a distance of 20cm at the axial spout,the bubble crushing and aggregation were stabilized. When the spout diameter is 0.5mm,the mostly bubble particle sizes are in the range of 100 to 300μm,suitable to the bubble conditions for removal of PM_2.5. As the solution temperature increases,the number of atomized bubble particles of 0 to 300μm is increased significantly.

Key words: foam, agglomeration, bubble, atomized particle size, visualization, image processing

摘要： 泡沫团聚法是有效脱除细颗粒物PM_2.5的方法。本文对团聚液的雾化粒径进行了研究，筛选出适于团聚PM_2.5的气泡粒径的溶液及喷雾条件。文中首先对气泡粒径与团聚颗粒物的能力进行估算，进而通过CCD拍摄精细雾化喷嘴喷出的团聚液泡沫的流动过程，利用MATLAB处理图片，得出雾化气泡粒径和密度大小。实验结果表明，发泡剂会使团聚液的雾化液滴形成气泡，增大雾化颗粒直径；PAM团聚液形成的气泡粒径偏小，且雾化颗粒密度大，粒径主要分布在小于200μm范围；XTG团聚液气泡粒径偏大，CMC团聚液气泡粒径介于两者之间；0.2% CMC团聚液气泡粒径均匀，颗粒数量大；在距喷口轴向20cm处，气泡破碎和聚合趋于稳定；喷口直径0.5mm时，气泡雾化粒径大多分布在100~300μm粒径范围内，符合团聚脱除PM_2.5的气泡条件；随着温度的升高，直径在0~300μm内的气泡颗粒数量增大明显。

关键词: 泡沫, 团聚, 气泡, 雾化粒径, 可视化, 图像处理

CLC Number:

TQ056.1

ZHANG Longlong, AN Zewen, JIANG Xu, WANG Cuiping. Visualization study of reunion liquid atomization bubble size distribution characteristics[J]. Chemical Industry and Engineering Progree, 2016, 35(10): 3086-3091.

张龙龙, 安泽文, 姜旭, 王翠苹. 团聚液雾化气泡粒径分布特性的可视化研究[J]. 化工进展, 2016, 35(10): 3086-3091.

References

[1] 张卫风,廖春玲.我国超细颗粒物PM_2.5团聚技术研究进展[J].华东交通大学学报,2015,32(4):124-130.
[2] 赵汶,刘勇,鲍静静,等.化学团聚促进燃煤细颗粒物脱除的试验研究[J].中国电机工程学报,2013(20):52-58
[3] LIU Z,LIU H,FENG X,et al.Simulation for the flow field of the turbulence coalescence device and the trajectory of particles[J].Proceedings of the Csee,2012,32(14):71-75.
[4] 刘勇,赵汶,刘瑞,等.化学团聚促进电除尘脱除PM_2.5的实验研究[J].化工学报,2014,65(9):3609-3616.
[5] 陈俊.燃煤超细颗粒物团聚的实验研究[D].武汉:华中科技大学,2005.
[6] 陈小艳,周骛,蔡小舒,等.大型喷雾粒径分布的图像法测量[J].化工学报,2014,65(2):480-487.
[7] 屈健,王谦,韩新月,等.大深宽比双T形微通道内液-液两相流可视化研究[J].化工进展,2014,33(10):2583-2587.
[8] 卢庆.柴油机喷油泵喷油量快速自动测量方法及试验装置的研究[J].科技资讯,2008(22):23-23.
[9] 张琳,崔腾飞,蒋枫,等.升膜蒸发管内流型可视化及传热性能[J].化工进展,2015,34(5):1259-1263.
[10] ALI B A,PUSHPAVANAM S.Experimental and computational investigation of two phase gas-liquid flows:point source injection at the center[J].Ind.Eng.Chem.Res,2011,50(23):13220-13229.
[11] ELSINGA G E,SCARANO F,WIENEKE B,et al.Tomographic particle image velocimetry[J].Experiments in Fluids,2006,41(4):933-947.
[12] GADGIL H P,DOLATABADI A,RAGHUNANDAN B N.Mass distribution studies in effervescent sprays[J].Atomization&Sprays,2011,21(5):375-390.
[13] 张晶晶.基于单帧单曝光图像法的多相流速度场和粒度分布测量研究[D].上海:上海理工大学,2011.
[14] 金春玉.空心圆锥雾化喷嘴喷雾实验与数值研究[D].上海:上海交通大学,2007
[15] JEONG H,LEE K,IKEDA Y,et al.Investigation of the spray characteristics for a secondary fuel injection nozzle using a digital image processing method[J].Measurement Science&Technology,2007,18(5):1591-1602.
[16] 李静,姜曼松.数字图像处理对雾化粒度测量的研究[J].船海工程,2001(s2):100-102.
[17] 张丹丹,赵维梅,肖代明,等.十二烷基苯磺酸钠表面张力的研究[J].辽宁化工,2012,41(7):678-679,682.