Effect of jet impingement nanofluid on heat transfer characteristics of semicircular spiral channels

doi:10.16085/j.issn.1000-6613.2023-0106

Abstract

Abstract:

To improve the heat exchange effect of the semicircular spiral channel outside the tubular reactor, a jet inlet was set on the wall of the traditional spiral channel. Three kinds of nanofluids (CuO-H₂O, Al₂O₃-H₂O and TiO₂-H₂O) were used as heat transfer fluids, respectively. Based on Mixture mixing model, the influence of different nanofluids on the heat exchange and flow characteristics of the semi-circular spiral channel at different Re(10000—36000) and jet velocity ratios was investigated. The heat transfer enhancement factors PEC_j0 and PEC_j were used to evaluate the comprehensive heat transfer enhancement before and after increasing the jet flow in the semi-circular spiral channel. The results showed that at the jet speed ratio ε=0—5, the pressure drop of Al₂O₃-H₂O nanofluids was highest, while that of CuO-H₂O nanofluids was lowest. Al₂O₃-H₂O nanofluids exhibited the best heat transfer performance at ε=0, with the average Nu number 1.31 times that of H₂O. Compared to ε=0, the average Nu_m of the spiral channel increased by 52.01% at ε=1—5. With the increased jet velocity ratio, the higher the turbulent kinetic energy, the better the mixing effect between jet fluid and main stream fluid. The influence range of jet fluid at each velocity ratio was 0°≤θ_j≤50°. When ε=3, the spiral channel generates three vortex structures. PEC_j0 increased first and then decreased with the rising Re, reaching its maximum value at Re=20173, while PEC_j increased with the rising jet velocity ratio. Overall, the heat transfer enhancement effect of jet impinging on Al₂O₃-H₂O nanofluids in spiral channels was the best in this study.

Key words: semicircular spiral channel, nanofluids, jet, enhanced heat transfer, numerical simulation

摘要：

为提高管式反应器外半圆形螺旋通道的换热效果，在传统螺旋通道壁面上设置了射流入口，采用三种纳米流体（CuO-H₂O、Al₂O₃-H₂O和TiO₂-H₂O）作为传热流体，基于Mixture混合模型探究了不同纳米流体在不同Re=10000~36000、不同射速比下对半圆形螺旋通道换热和流动特性的影响规律，并利用传热强化因子PEC_j0和PEC_j分别评价了半圆形螺旋通道增加射流前后的综合强化传热性能。研究结果表明：在射速比ε=0~5时，Al₂O₃-H₂O纳米流体的压降最大，CuO-H₂O纳米流体的压降最小。在ε=0时Al₂O₃-H₂O纳米流体的传热效果最好，其平均Nu数是H₂O的1.31倍。与ε=0相比，在ε=1~5工况下，螺旋通道平均Nu_m最高提升了52.01%。随着射速比的增加湍动能越大，射流与主流混合效果越好。各射速比工况下射流冲击的影响范围为0°≤θ_j≤50°，在ε=3时，螺旋通道产生三涡结构。PEC_j0随Re先增加后降低，在Re=20173时取得最大值，PEC_j随射速比的增大而增大。综合对比，射流冲击Al₂O₃-H₂O纳米流体对螺旋通道传热提升效果最佳。

关键词: 半圆形螺旋通道, 纳米流体, 射流, 强化传热, 数值模拟

CLC Number:

TK124

WANG Chao, WANG Zongyong, ZHANG Wei, HAN Xu, LIU Lei, FU Qihui. Effect of jet impingement nanofluid on heat transfer characteristics of semicircular spiral channels[J]. Chemical Industry and Engineering Progress, 2023, 42(12): 6207-6217.

王超, 王宗勇, 张伟, 韩旭, 刘磊, 付启慧. 射流冲击纳米流体对半圆形螺旋通道传热特性的影响[J]. 化工进展, 2023, 42(12): 6207-6217.

Figures/Tables 15

References 12

12	FU Tao. The effect of temperature on the specific heat capacity of heat transfer oil based on nanofluids[D]. Zhuzhou: Hunan University of Technology, 2021: 21-24.
13	吴华杰, 张善文, 张燕军. 纳米流体微通道流动换热数值模拟研究[J]. 低温与超导, 2021, 49(11): 66-72.
	WU Huajie, ZHANG Shanwen, ZHANG Yanjun. Numerical simulation of flow and heat transfer characteristics of nanofluids in microchannels[J]. Cryogenics & Superconductivity, 2021, 49(11): 66-72.
14	杨丽媛. 椭圆管内TiO₂-H₂O纳米流体传热与流动特性研究[D]. 徐州: 中国矿业大学, 2019: 18-29.
	YANG Liyuan. Study on heat transfer and flow characteristics of TiO₂-H₂O nanofluids in elliptical tubes[D]. Xuzhou: China University of Mining and Technology, 2019: 18-29.
15	张明建. 纳米流体在管内流动换热的数值研究[D]. 济南: 山东大学, 2020: 12-24.
	ZHANG Mingjian. Numerical study on heat transfer of nanoaluid flowing in a tube[D]. Jinan: Shandong University, 2020: 12-24.
16	苏婷. 新型强化传热技术及其强化机理的数值模拟研究[D]. 南昌: 南昌大学, 2010: 12-16.
	SU Ting. The numerical simulation on new heat transfer enhancement technology and enhancement mechanism[D]. Nanchang: Nanchang University, 2010: 12-16.
17	HWANG Kyo Sik, Hyo Jun HA, LEE Seung Hyun, et al. Flow and convective heat transfer characteristics of nanofluids with various shapes of alumina nanoparticles[C]//Proceedings of ASME 2009 Second International Conference on Micro/Nanoscale Heat and Mass Transfer, December 18-21, 2009, Shanghai, China. 2010: 455-460.
18	NARREIN K, MOHAMMED H A. Influence of nanofluids and rotation on helically coiled tube heat exchanger performance[J]. Thermochimica Acta, 2013, 564: 13-23.
19	MOHAMMED Mohammed K, ABDOLBAQI M K, IBRAHIM Thamir K, et al. Experimental and numerical investigation of heat transfer enhancement using Al₂O₃-ethylene glycol/water nanofluids in straight channel[J]. MATEC Web of Conferences, 2018, 225: 01019.
20	YIN Xiang, KOU Guangxiao, XU Aixiang, et al. Effects of TiO₂ nanoparticles on thermal conductivity of heat transfer oil[J]. Journal of Central South University, 2019, 26(8): 2129-2135.
21	卫利峰, 高文志, 李勇, 等. 螺旋椭圆管换热器传热特性与阻力特性研究[J]. 化学工程, 2019, 47(4): 23-28.
	WEI Lifeng, GAO Wenzhi, LI Yong, et al. Research on heat transfer and resistance characteristics of spiral oval tubes heat exchanger[J]. Chemical Engineering (China), 2019, 47(4): 23-28.
22	林清宇, 刘鹏辉, 冯振飞, 等. 螺旋通道内流体流动与传热特性研究进展[J]. 科学通报, 2017, 62(25): 2931-2940.
	LIN Qingyu, LIU Penghui, FENG Zhenfei, et al. A review on fluid flow and heat transfer in helical channel[J]. Chinese Science Bulletin, 2017, 62(25): 2931-2940.
23	ZHAI Xinfeng, QI Cong, PAN Yuhang, et al. Effects of screw pitches and rotation angles on flow and heat transfer characteristics of nanofluids in spiral tubes[J]. International Journal of Heat and Mass Transfer, 2019, 130: 989-1003.
1	张静, 张艳秋, 吴剑华. 螺距和搭接对螺旋半管夹套强化传热的影响[J]. 过程工程学报, 2017, 17(4): 697-703.
	ZHANG Jing, ZHANG Yanqiu, WU Jianhua. Effect of varying pitch and overlap scale on enhanced heat transfer of half-coil jackets[J]. The Chinese Journal of Process Engineering, 2017, 17(4): 697-703.
2	LI Yaxia, WU Jianhua, ZHAN Hongren, et al. Fluid flow and heat transfer characteristic of outer and inner half coil jackets[J]. Chinese Journal of Chemical Engineering, 2011, 19(2): 253-261.
3	李雅侠, 吴剑华, 龚斌, 等. 螺旋半圆管夹套内湍流流动与传热的数值模拟[J]. 过程工程学报, 2010, 10(4): 644-649.
	LI Yaxia, WU Jianhua, GONG Bin, et al. Numerical research on fluid turbulent flow and heat transfer in the half-coil jackets[J]. The Chinese Journal of Process Engineering, 2010, 10(4): 644-649.
4	李雅侠, 华博, 吴剑华, 等. 釜内螺旋半圆管夹套内流体湍流流动特性[J]. 过程工程学报, 2011, 11(6): 913-918.
	LI Yaxia, HUA Bo, WU Jianhua, et al. Flow characteristics of turbulent fluid in the inner half-coil jackets of an autoclave[J]. The Chinese Journal of Process Engineering, 2011, 11(6): 913-918.
5	李雅侠, 王航, 吴剑华. 螺旋半圆管夹套内充分发展层流流动与换热特性[J]. 化工学报, 2010, 61(11): 2796-2803.
	LI Yaxia, WANG Hang, WU Jianhua. Fully developed laminar flow and heat transfer characteristics in half-coil jackets[J]. CIESC Journal, 2010, 61(11): 2796-2803.
6	李雅侠, 吴凯, 史晓航, 等. 矩形翼强化半圆螺旋通道内流体流动与换热[J]. 沈阳化工大学学报, 2021, 35(1): 54-60.
	LI Yaxia, WU Kai, SHI Xiaohang, et al. Rectangular wings enhance fluid flow and heat transfer in semicircular spiral channel[J]. Journal of Shenyang University of Chemical Technology, 2021, 35(1): 54-60.
7	李雅侠, 许鹏宇, 韩泽民, 等. 矩形截面高宽比对射流强化螺旋通道传热性能的影响[J]. 过程工程学报, 2022, 22(5): 612-621.
	LI Yaxia, XU Pengyu, HAN Zemin, et al. Influence of aspect ratio on heat transfer enhancement performance by jet in helical duct with rectangular cross section[J]. The Chinese Journal of Process Engineering, 2022, 22(5): 612-621.
8	于峰, 李强, 宣益民. 纳米流体射流冲击冷却技术的实验研究[J]. 工程热物理学报, 2010, 31(12): 2097-2100.
	YU Feng, LI Qiang, XUAN Yimin. Experimental investigation of submerged impinging jet using nanofluids[J]. Journal of Engineering Thermophysics, 2010, 31(12): 2097-2100.
9	LI Yaxia, WANG Kai, WU Kai, et al. Research on heat transfer augment of the helical half-pipe jacket by jet longitudinal vortex generator[J]. Chemical Engineering and Processing—Process Intensification, 2022, 181: 109158.
10	CHOI S U, EASTMAN J A. Office of scientific & technical information technical reports: Enhancing thermal conductivity of fluids with nanoparticles[R]. US: Argonne National Laboratory,1995: 99-103.
11	禹言芳, 陈雅鑫, 孟辉波, 等. Lightnin静态混合器内纳米流体湍流传热特性分析[J]. 化工进展, 2021, 40(S2): 30-39.
	YU Yanfang, CHEN Yaxin, MENG Huibo, et al. Analysis of turbulent heat transfer characteristics of nanofluids in the Lightnin static mixer[J]. Chemical Industry and Engineering Progress, 2021, 40(S2): 30-39.
12	符涛. 温度对导热油基纳米流体比热容影响规律研究[D]. 株洲: 湖南工业大学, 2021: 21-24.

物质	密度ρ_p/kg∙m^-3	比热容c_p /J∙kg^-1∙K^-1	黏度μ_p/kg∙m^-1∙s^-1	热导率λ_p/W∙m^-1∙K^-1
H₂O	998.2	4182	0.001003	0.6
Al₂O₃	3600	765	—	36
CuO	6510	540	—	18
TiO₂	4260	216	—	6.5

物质	密度ρ_p/kg∙m^-3	比热容c_p /J∙kg^-1∙K^-1	黏度μ_p/kg∙m^-1∙s^-1	热导率λ_p/W∙m^-1∙K^-1
H₂O	998.2	4182	0.001003	0.6
Al₂O₃	3600	765	—	36
CuO	6510	540	—	18
TiO₂	4260	216	—	6.5

[1]	WANG Tai, SU Shuo, LI Shengrui, MA Xiaolong, LIU Chuntao. Dynamic behavior of single bubble attached to the solid wall in the AC electric field [J]. Chemical Industry and Engineering Progress, 2023, 42(S1): 133-141.
[2]	CHEN Kuangyin, LI Ruilan, TONG Yang, SHEN Jianhua. Structure design of gas diffusion layer in proton exchange membrane fuel cell [J]. Chemical Industry and Engineering Progress, 2023, 42(S1): 246-259.
[3]	YANG Yudi, LI Wentao, QIAN Yongkang, HUI Junhong. Analysis of influencing factors of natural gas turbulent diffusion flame length in industrial combustion chamber [J]. Chemical Industry and Engineering Progress, 2023, 42(S1): 267-275.
[4]	GUO Qiang, ZHAO Wenkai, XIAO Yonghou. Numerical simulation of enhancing fluid perturbation to improve separation of dimethyl sulfide/nitrogen via pressure swing adsorption [J]. Chemical Industry and Engineering Progress, 2023, 42(S1): 64-72.
[5]	SHAO Boshi, TAN Hongbo. Simulation on the enhancement of cryogenic removal of volatile organic compounds by sawtooth plate [J]. Chemical Industry and Engineering Progress, 2023, 42(S1): 84-93.
[6]	CHEN Lin, XU Peiyuan, ZHANG Xiaohui, CHEN Jie, XU Zhenjun, CHEN Jiaxiang, MI Xiaoguang, FENG Yongchang, MEI Deqing. Investigation on the LNG mixed refrigerant flow and heat transfer characteristics in coil-wounded heat exchanger (CWHE) system [J]. Chemical Industry and Engineering Progress, 2023, 42(9): 4496-4503.
[7]	LIU Xuanlin, WANG Yikai, DAI Suzhou, YIN Yonggao. Analysis and optimization of decomposition reactor based on ammonium carbamate in heat pump [J]. Chemical Industry and Engineering Progress, 2023, 42(9): 4522-4530.
[8]	ZHAO Xi, MA Haoran, LI Ping, HUANG Ailing. Simulation analysis and optimization design of mixing performance of staggered impact micromixer [J]. Chemical Industry and Engineering Progress, 2023, 42(9): 4559-4572.
[9]	ZHANG Dailing, DING Yumei, ZUO Xiahua, LI Haowei, YANG Weimin, YAN Hua, AN Ying. Photothermal characteristics of waste toner nanofluids [J]. Chemical Industry and Engineering Progress, 2023, 42(9): 4791-4798.
[10]	ZHANG Chao, YANG Peng, LIU Guanglin, ZHAO Wei, YANG Xufei, ZHANG Wei, YU Bo. Influence of surface microstructure on arrayed microjet flow boiling heat transfer [J]. Chemical Industry and Engineering Progress, 2023, 42(8): 4193-4203.
[11]	YE Zhendong, LIU Han, LYU Jing, ZHANG Yaning, LIU Hongzhi. Optimization of thermochemical energy storage reactor based on calcium and magnesium binary salt hydrates [J]. Chemical Industry and Engineering Progress, 2023, 42(8): 4307-4314.
[12]	YU Junnan, YU Jianfeng, CHENG Yang, QI Yibo, HUA Chunjian, JIANG Yi. Performance prediction of variable-width microfluidic concentration gradient chips by deep learning [J]. Chemical Industry and Engineering Progress, 2023, 42(7): 3383-3393.
[13]	SHAN Xueying, ZHANG Meng, ZHANG Jiafu, LI Lingyu, SONG Yan, LI Jinchun. Numerical simulation of combustion of flame retardant epoxy resin [J]. Chemical Industry and Engineering Progress, 2023, 42(7): 3413-3419.
[14]	WANG Shuo, ZHANG Yaxin, ZHU Botao. Prediction of erosion life of coal water slurry pipeline based on grey prediction model [J]. Chemical Industry and Engineering Progress, 2023, 42(7): 3431-3442.
[15]	ZHOU Longda, ZHAO Lixin, XU Baorui, ZHANG Shuang, LIU Lin. Advances in electrostatic-cyclonic coupling enhanced multiphase media separation research [J]. Chemical Industry and Engineering Progress, 2023, 42(7): 3443-3456.