Chemical Industry and Engineering Progress ›› 2019, Vol. 38 ›› Issue (07): 3291-3296.DOI: 10.16085/j.issn.1000-6613.2018-2026

• Materials science and technology • Previous Articles     Next Articles

Effect of drying temperature on the structure and properties of nano graphene oxide/PHBH composite films

Yujuan QIU1(),Xiaojun MA1(),Xing YIN2   

  1. 1. Tianjin University of Science and Technology,Tianjin 300222,China
    2. School of Packing and Printing Engineering, Tianjin Vocational Institute,Tianjin 300410,China
  • Received:2018-10-12 Online:2019-07-05 Published:2019-07-05
  • Contact: Xiaojun MA

干燥温度对纳米氧化石墨烯/PHBH复合膜结构及性能的影响

邱玉娟1(),马晓军1(),尹兴2   

  1. 1. 天津科技大学包装与印刷工程学院,天津 300222
    2. 天津职业大学包装与印刷工程学院,天津 300410
  • 通讯作者: 马晓军
  • 作者简介:邱玉娟(1993—),女,硕士研究生,研究方向为生物基高分子材料。E-mail:<email>13102122533@163.com</email>。
  • 基金资助:
    天津市自然科学基金(18JCYBJC90100)

Abstract:

The effects of different drying temperatures on the structure and properties of nano graphene oxide (GO)/poly(3-hydroxybutyrate-co-3-hydroxy-hexanoate)(PHBH) composite films prepared by solution casting method, were studied by SEM, XRD, DSC, tensile, transparency and barrier tests. The results show that the dispersion of GO in PHBH, crystallization, elongation at break and barrier properties of GO/PHBH composite films increase firstly and then decrease, while the tensile strength and transparency of GO/PHBH film increase gradually, with the increase of drying temperature. When the drying temperature is gradient elevation of temperature (45℃→55℃), the tensile strength, elongation at break, oxygen transmission rate and water vapor transmission rate of GO/PHBH film with smooth cross-section, good dispersion, crystallinity, thermal stability, mechanical and barrier properties can reach 20.11MPa, 17.47%, 48cm3/(m2·d) and 13.33g/(cm2·d), respectively. And the comprehensive performance of GO/PHBH film prepared at the temperature is better than that of others.

Key words: graphene oxide, poly(3-hydroxybutyrate-co-3-hydroxyhexanoate), solution casting method, drying temperature, structure properties

摘要:

通过溶液浇铸法制备得到纳米氧化石墨烯(GO)/聚羟基丁酸-羟基己酸酯(PHBH)复合膜,利用SEM、XRD、DSC、拉伸测试、阻隔测试及透明度测试等检测手段,研究了不同干燥温度对复合膜结构及性能的影响,优化了制备工艺。结果表明:随着干燥温度的升高,GO在PHBH中的分散性以及复合膜的结晶度、断裂伸长率和阻隔性先增加后减小,而拉伸强度及透光率则随温度的增加而增加。当干燥温度为45℃→55℃梯度升温时,GO在PHBH中均匀分散,且复合膜的断面光滑,有良好的结晶度、热稳定性、力学及阻隔性能,其拉伸强度、断裂伸长率可分别达到20.11MPa、17.47%,且透氧系数及水蒸气透过系数分别为48cm3/(m2·d)、13.33g/(cm2·d),综合性能优于其他干燥温度下的复合膜。

关键词: 氧化石墨烯, 聚羟基丁酸-羟基己酸酯, 溶液浇铸法, 干燥温度, 结构性能

CLC Number: 

京ICP备12046843号-2;京公网安备 11010102001994号
Copyright © Chemical Industry and Engineering Progress, All Rights Reserved.
E-mail: hgjz@cip.com.cn
Powered by Beijing Magtech Co. Ltd