不同充液率平板热管性能实验

doi:10.16085/j.issn.1000-6613.2018-1520

摘要/Abstract

摘要：

搭建了平板热管测试实验台，对不同充液率下热管性能进行了实验研究，并以最佳充液率的热管为研究对象，分析了加热功率、冷却水温及冷却水流速对热管性能的影响。实验结果表明：充液率为20%和30%时热管在各加热功率下展现了良好的性能，最小热阻为0.18℃/W和0.19℃/W，热导率为8158W/(m·℃)和8540W/(m·℃)。由于沸腾换热滞后性，相较于功率增加，功率减少时热管性能更优，同等加热功率条件下蒸发段温度更低。功率增加和功率减少对热管蒸发段热阻影响较大，而冷凝段热阻几乎不受影响。当冷却水温为17℃和22℃时，热管蒸发段温度比冷却水温为7℃和12℃时蒸发段温度低2℃左右。相较于冷却水温22℃时，冷却水温为17℃时热管蒸发段温度能更快达到稳定值。冷却水流速影响蒸发段温度及达到稳定运行的时间，实验表明热管工作的最佳冷却水流速为5.81g/s。

关键词: 平板热管, 微通道, 相变, 传热, 热阻, 热导率

Abstract:

A test bed on flat plate heat pipe was built in order to study heat pipe performance with different filling ratios. Then the heat pipe with the best filling ratio was taken into account as the research object, the influences of increasing heating power, decreasing heat power, cooling water temperature and mass flow rate on heat pipe performance were analyzed. The results showed that heat pipe with filling ratio of 20% and 30% presented a good performance. The minimum thermal resistance was 0.18℃/W and 0.19℃/W, with the maximum effective thermal conductivity of 8158W/(m·℃) and 8540W/(m·℃), respectively. Compared to heat pipe performance with the increase heating power, the performance with the decrease heating power was better because of boiling hysteresis phenomenon, and evaporation section temperature was lower at the same heating power. The effect on thermal resistance of evaporation section was great with increasing and decreasing heating power, but the thermal resistance of condensation section was almost unaffected. The heat pipe evaporation section temperature with cooling water temperature of 17℃ and 22℃ was about 2℃ lower than that with cooling water temperature of 7℃ and 12℃. Compared to cooling water temperature of 22℃, evaporation temperature of heat pipe reached a stable value more quickly when cooling water temperature was 17℃. Thus, the heat pipe performance was best when cooling water temperature was 17℃. Synthesizes evaporation temperature, the time achieving a stable and water pump power consumption, the best mass flow rate for heat pipe was 5.81g/s.

Key words: flat plate heat pipe, micro channels, phase change, heat transfer, thermal resistance, thermal conductivity

中图分类号:

TK172.4

王岗, 赵耀华, 全贞花, 王宏燕. 不同充液率平板热管性能实验[J]. 化工进展, 2019, 38(05): 2123-2131.

Gang WANG, Yaohua ZHAO, Zhenhua QUAN, Hongyan WANG. Characteristic of flat plate heat pipe with different filling ratios[J]. Chemical Industry and Engineering Progress, 2019, 38(05): 2123-2131.

图/表 14

图1 平板热管截面图（单位：mm）

图2 系统测试原理图

图3 系统测点布置图（单位：mm）

图4 系统热损失分析

图5 蒸发段温度随加热功率变化

图6 热阻随加热功率变化

图7 热导率随加热功率变化

图8 功率增加时各点温度变化

图9 功率减少时各点温度变化

图10 热管热阻随加热功率的变化

图11 蒸发段热阻随加热功率的变化

图12 冷凝段热阻随加热功率的变化

图13 冷却水温度对热管蒸发段温度影响

图14 冷却水流速对热管蒸发段温度影响

参考文献 25

1	YAU Y H，AHMADZADEHTALATAPEHM. A review on the application of horizontal heat pipe heat exchangers in air conditioning systems in the tropics[J]. Applied Thermal Engineering，2010，30（2/3）：77-84.
2	ALY W I A，ELBALSHOUNYM A，El-HameedH M A，et al. Thermal performance evaluation of a helically-micro-grooved heat pipe working with water and aqueous Al₂O₃ nanofluid at different inclination angle and filling ratio[J]. Applied Thermal Engineering，2017，110：1294-1304.
3	YANGX，YANY Y，MULLEND. Recent developments of lightweight, high performance heat pipes[J]. Applied Thermal Engineering，2012，s 33/34（1）：1-14.
4	ALAWIO A，SIDIKN A C，MOHAMMEDH A，et al. Fluid flow and heat transfer characteristics of nanofluids in heat pipes：a review[J]. International Communications in Heat & Mass Transfer，2014，56（8）：50-62.
5	PETERSONG P. An introduction to heat pipes: modeling, testing, and applications[M]. New York: Wiley -Interscience ，1994.
6	JANICKIM, NAPIERALSKIA. Modeling electronic circuit radiation cooling using analytical thermal model[J]. Microelectronics Journal，2000，31（9/10）：781-785.
7	KHRUSTALEVD, FAGHRIA. Heat transfer in the inverted meniscus type evaporator at high heat fluxes[J]. International Journal of Heat & Mass Transfer，1995，38（16）：3091-3101.
8	CHENS W，HSIEHJ C，CHOUC T，et al. Experimental investigation and visualization on capillary and boiling limits of micro-grooves made by different processes[J]. Sensors & Actuators A: Physical，2007，139（1）：78-87.
9	LIPSS，LEFEVREF，BONJOURJ. Nucleate boiling in a flat grooved heat pipe[J]. International Journal of Thermal Sciences，2009，48（7）：1273-1278.
10	LIPSS，LEFEVREF，BONJOURJ. Physical mechanisms involved in grooved flat heat pipes: experimental and numerical analyses[J]. International Journal of Thermal Sciences，2011，50（7）：1243-1252.
11	LIPSS，LEFEVREF，BONJOURJ. Combined effects of the filling ratio and the vapour space thickness on the performance of a flat plate heat pipe[J]. International Journal of Heat & Mass Transfer，2010，53（4）：694-702.
12	SUPOWITJ，HEFLINGERT，STUBBLEBINEM，et al. Designer fluid performance and inclination angle effects in a flat grooved heat pipe[J]. Applied Thermal Engineering，2016，101：770-777.
13	XUP，LIQ. Visualization study on the enhancement of heat transfer for the groove flat-plate heat pipe with nanoflower coated CuO layer[J]. Applied Physics Letters，2017，111（14）：141609.
14	HOPKINSR，FAGHRIA. Flat miniature heat pipes with micro capillary grooves[J]. Transactions of the Asme Serie C: Journal of Heat Transfer，1999，121（1）：102-109.
15	WONGS C，CHENC W. Visualization and evaporator resistance measurement for a groove-wicked flat-plate heat pipe[J]. International Journal of Heat & Mass Transfer，2012，55（9/10）：2229-2234.
16	LAUNAYS，SARTREV，LALLEMANDM. Experimental study on silicon micro-heat pipe arrays[J]. Applied Thermal Engineering，2004，24（2）：233-243.
17	LEBERREM，LAUNAYS，SARTREV，et al. Fabrication and experimental investigation of silicon micro heat pipes for cooling electronics[J]. Journal of Micromechanics & Microengineering，2003，13（3）：436.
18	DEANR N，HARRISD K，PALKARA Y，et al. Liquid metal-filled micro heat pipes for thermal management of solid-state devices[J]. IEEE Transactions on Industrial Electronics，2012，59（12）：4888-4894.
19	SOLOMONA B，KUMARA M R，RAMACHANDRANK，et al. Characterisation of a grooved heat pipe with an anodised surface[J]. Heat & Mass Transfer，2016，53（3）：1-11.
20	KIM H J，LEE S H，KIM S B，et al. The effect of nanoparticle shape on the thermal resistance of a flat-plate heat pipe using acetone-based Al₂O₃ nanofluids[J]. International Journal of Heat & Mass Transfer，2016，92：572-577.
21	HAOX H，PENGB，CHENY，et al. Experimental investigation on heat transfer performance of a flat plate heat pipe with MWCNTS-acetone nanofluid[J]. Journal of Heat Transfer-transactions of the ASME，2017,139（6）：062001.
22	ALIJANIH，ÇETINB，AKKUSY，et al. Effect of design and operating parameters on the thermal performance of aluminum flat grooved heat pipes[J]. Applied Thermal Engineering，2018，132：174-187.
23	STUBBLEBINEM J，CATTONI. Passivation and performance of inorganic aqueous solutions in a grooved aluminum flat heat pipe[J]. Journal of Heat Transfer，2015，137（5）：052901.
24	TANGH，TANGY，YUANW，et al. Fabrication and capillary characterization of axially micro-grooved wicks for aluminium flat-plate heat pipes[J]. Applied Thermal Engineering，2018，129：907-915.
25	王宏燕，赵耀华. 平板微热管阵列垂直传热的数值分析[J]. 化工学报，2014，65（2）：508-515.
	WANGH Y，ZHAOY H. Numerical investigation on heat transfer of vertical micro-heat pipe arrays[J]. CIESC Journal，2014，65（2）：508-515.

[1]	肖辉, 张显均, 兰治科, 王苏豪, 王盛. 液态金属绕流管束流动传热进展[J]. 化工进展, 2023, 42(S1): 10-20.
[2]	赵晨, 苗天泽, 张朝阳, 洪芳军, 汪大海. 负压状态窄缝通道乙二醇水溶液传热特性[J]. 化工进展, 2023, 42(S1): 148-157.
[3]	陈林, 徐培渊, 张晓慧, 陈杰, 徐振军, 陈嘉祥, 密晓光, 冯永昌, 梅德清. 液化天然气绕管式换热器壳侧混合工质流动及传热特性[J]. 化工进展, 2023, 42(9): 4496-4503.
[4]	徐茂淯, 陶帅, 齐聪, 梁林. 圆盘式环路热管的启动特性及温度波动[J]. 化工进展, 2023, 42(9): 4531-4537.
[5]	时雨, 赵运超, 樊智轩, 蒋达华. 夏热冬冷地区相变屋面最佳相变温度的实验研究[J]. 化工进展, 2023, 42(9): 4828-4836.
[6]	卜治丞, 焦波, 林海花, 孙洪源. 脉动热管计算流体力学模型与研究进展[J]. 化工进展, 2023, 42(8): 4167-4181.
[7]	张超, 杨鹏, 刘广林, 赵伟, 杨绪飞, 张伟, 宇波. 表面微结构对阵列微射流沸腾换热的影响[J]. 化工进展, 2023, 42(8): 4193-4203.
[8]	汪健生, 张辉鹏, 刘雪玲, 傅煜郭, 朱剑啸. 多孔介质结构对储层内流动和换热特性的影响[J]. 化工进展, 2023, 42(8): 4212-4220.
[9]	王云刚, 焦健, 邓世丰, 赵钦新, 邵怀爽. 冷凝换热与协同脱硫性能实验分析[J]. 化工进展, 2023, 42(8): 4230-4237.
[10]	汤磊, 曾德森, 凌子夜, 张正国, 方晓明. 相变蓄冷材料及系统应用研究进展[J]. 化工进展, 2023, 42(8): 4322-4339.
[11]	俞俊楠, 俞建峰, 程洋, 齐一搏, 化春键, 蒋毅. 基于深度学习的变宽度浓度梯度芯片性能预测[J]. 化工进展, 2023, 42(7): 3383-3393.
[12]	陈蔚阳, 宋欣, 殷亚然, 张先明, 朱春英, 付涛涛, 马友光. 矩形微通道内液相黏度对气泡界面的作用机制[J]. 化工进展, 2023, 42(7): 3468-3477.
[13]	董晓珊, 王建, 林法伟, 颜蓓蓓, 陈冠益. 基于钙钛矿氧化物的金属纳米粒子溶出策略：溶出过程、驱动力及控制策略[J]. 化工进展, 2023, 42(6): 3049-3065.
[14]	陶梦琦, 刘美红, 康宇驰. 基于micro-PIV的微通道内流体绕流单微圆柱和并联双微圆柱流场特性[J]. 化工进展, 2023, 42(6): 2836-2844.
[15]	刘厚励, 顾中浩, 阳康, 张莉. 3D打印槽道结构槽宽对池沸腾传热特性的影响[J]. 化工进展, 2023, 42(5): 2282-2288.