Pressure drop of gas-liquid two phase co-current flowing down through the orifice unit of sieve plate

doi:10.16085/j.issn.1000-6613.2019-0625

Abstract

Abstract:

For the basic unit of stacked sieve plate packing, 12 orifice plates were used to study the pressure drop characteristics of gas-liquid two-phase co-current flowing down through the orifice, and the influence of flowrates and the orifice plate structure was clarified. The experimental results showed that the pressure drop increases with the increase of gas-liquid flow rate, decreases with the increase of orifice diameter. In the usual thickness range of the sieve plate, the pressure drop increases with the decrease of plate thickness due to the sharp edge effect of the orifice. According to the different behaviors of the pressure, the pressure drop prediction correlation of a single gas phase downward through the orifice was established with the Reynolds number of 5000 as the demarcation. When the gas Reynolds number is greater than 5000, the correlation is modified by using the gas phase conversion factor, and the pressure drop prediction correlation of gas-liquid two phases flowing down through the orifice was obtained. When the gas Reynolds number is less than 5000, the prediction correlation of gas-liquid two-phase pressure drop in the corresponding range of gas Reynolds number was obtained by directly modifying the single gas resistance coefficient.

Key words: stacked sieve plate packing, orifice unit, gas-liquid flow, pressure drop, correlation

摘要：

针对堆叠筛板填料的基本单元，采用12种不同规格的孔板，研究了气液两相并流向下通过孔口的压降特性，阐明了气液流量、孔板结构对压降的影响规律。结果表明：压降随气液流量的增加而增大；随孔径的增大而减小；在筛板常用厚度范围内，孔口锐缘效应使得压降随板厚减小而增大。根据孔口压降行为不同，以气相雷诺数Re_G=5000分界，建立了单一气相向下通过孔口的压降预测关联式；然后利用气相折算因子对关联式进行修正，得到了Re_G>5000时气液并流向下通过孔口的压降预测关联式；当Re_G<5000时，通过直接对单一气相阻力系数进行修正，得到了相应气相雷诺数范围内的气液两相压降预测关联式。

关键词: 堆叠筛板填料, 孔口单元, 气液两相流, 压降, 预测关联式

CLC Number:

TQ 021.1

Anqi ZHANG,Min QIAO,Shaoxun WU,Yu MAO,Weixing HUANG. Pressure drop of gas-liquid two phase co-current flowing down through the orifice unit of sieve plate[J]. Chemical Industry and Engineering Progress, 2020, 39(1): 49-55.

张安琪,谯敏,武劭恂,毛宇,黄卫星. 气液两相并流向下通过筛板孔口单元的压降特性[J]. 化工进展, 2020, 39(1): 49-55.

Figures/Tables 10

References 17

1	SHI W, HUANG W, ZHOU Y, et al. Hydrodynamics and pressure loss of concurrent gas-liquid downward flow through sieve plate packing[J]. Chemical Engineering Science, 2016, 143: 206-215.
2	姜鹏, 王琨, 谯敏, 等. 气液两相并流下行通过堆叠筛板填料的压降特性[J]. 化工学报, 2018, 69(8): 3373-3382.
	JIANG Peng, WANG Kun, QIAO Min, et al. Pressure drop of gas-liquid two phases parallelly flowing down through a stacked sieve plate packing[J]. CIESC Journal, 2018, 69(8): 3373-3382.
3	何杰, 单鹏飞, 谭长斌, 等. 填料塔气液并流接触时压降的研究[J]. 化学工业与工程, 2012, 29(4): 45-49.
	HE Jie, SHAN Pengfei, TAN Changbin, et al. Pressure drop of packed column in gas-liquid co-current flow[J]. Chemical Industry and Engineering, 2012, 29(4): 45-49.
4	毛明华, 李群生, 王爱军. 高效导向筛板流体力学性能研究[J]. 北京化工大学学报(自然科学版), 2004, 31(3): 27-30.
	MAO Minghua, LI Qunsheng, WANG Aijun. Hydrodynamic characteristics of high efficient flow-guided sieve tray[J]. Journal of Beijing University of Chemical Technology (Natural Science Edition), 2004, 31(3): 27-30.
5	KOJASOY G, LANDIS F, KWAME-MENSAH P, et al. Two-phase pressure drop in multiple thick- and thin-orifice plates[J]. Experimental Thermal and Fluid Science, 15(4): 347-358.
6	CHEN D K, CHEN Z H, ZHAO Z S, et al. The local resistance of gas-liquid two-phase flow through an orifice[J]. International Journal of Heat & Fluid Flow, 2012, 7(3): 231-238.
7	ROUL M K, DASH S K. Numerical modeling of pressure drop due to singlephase flow of water and two-phase flow of airwater mixtures through thick orifices[J]. International Journal of Engineering Trends & Technology, 2012, 3(4): 544-551.
8	FOSSA M, GUGLIELMINI G. Pressure drop and void fraction profiles during horizontal flow through thin and thick orifices[J]. Experimental Thermal & Fluid Science, 2002, 26(5): 513-523.
9	王宏, 安丽, 高彦宁,等. 气液并流筛板式填料压降的数值模拟[J]. 化工进展, 2013, 32(7): 1500-1505.
	WANG Hong, AN Li, GAO Yanning, et al. Simulation research on pressure drop of sieve tray type packing with gas-liquid co-current flow[J]. Chemical Industry and Engineering Progress, 2013, 32(7): 1500-1505.
10	张廷廷, 雷燃, 戴慧芳, 等. 两相管流压降计算及影响因素[J]. 油气储运, 2013, 32(7): 709-714.
	ZHANG Tingting, LEI Ran, DAI Huifang, et al. Pressure drop calculation and influential factor analysis on the two-phase pipe flow[J]. Oil & Gas Storage and Transportation, 2013, 32(7): 709-714.
11	HOLT G J, MAYNES D, BLOTTER J. Cavitation at sharp edge multi-hole baffle plates[C]// ASME International Mechanical Engineering Congress & Exposition, 2011.
12	FENG S, LIU Z, WEI L, et al. Effects of the orifice to pipe diameter ratio on orifice flows[J]. Chemical Engineering Science, 2016, 152: 497-506.
13	STICHLMAIR J, MERSMANN A. Dimensioning plate columns for absorption and rectification[J]. International Chemical Engineering, 1978, 18(2): 223-236.
14	GAN G, RIFFAT S B. Pressure loss characteristics of orifice and perforated plates[J]. Experimental Thermal & Fluid Science, 1997, 14(2): 160-165.
15	ROUL M. Numerical investigation of single-phase and two-phase flow through thin orifices in horizontal pipes[J]. Indian Journal of Science & Technology, 2012, 5(9): 3-4.
16	KOLODZIE JR P A, WINKLE M VAN. Discharge coefficients through perforated plates[J]. AIChE Journal, 2010, 3(3): 305-312.
17	ZHU X, YANG Z, BI Q. Experimental study on the pressure drop characteristics of steam-water two-phase flow at a low mass velocity in a four-head rifled tube[J]. Applied Thermal Engineering, 2017, 122: 148-157.

编号	d/mm	t/d	A₁/A₂
A	6	0.13	0.0017
B	6	0.5	0.0017
C	6	0.95	0.0017
D	6	1.33	0.0017
E	10	0.12	0.0047
F	10	0.49	0.0047
G	10	0.93	0.0047
H	10	1.37	0.0047
I	14	0.11	0.0091
J	14	0.53	0.0091
K	14	0.94	0.0091
L	14	1.24	0.0091

编号	d/mm	t/d	A₁/A₂
A	6	0.13	0.0017
B	6	0.5	0.0017
C	6	0.95	0.0017
D	6	1.33	0.0017
E	10	0.12	0.0047
F	10	0.49	0.0047
G	10	0.93	0.0047
H	10	1.37	0.0047
I	14	0.11	0.0091
J	14	0.53	0.0091
K	14	0.94	0.0091
L	14	1.24	0.0091

[1]	CHEN Kuangyin, LI Ruilan, TONG Yang, SHEN Jianhua. Structure design of gas diffusion layer in proton exchange membrane fuel cell [J]. Chemical Industry and Engineering Progress, 2023, 42(S1): 246-259.
[2]	ZHAO Chen, MIAO Tianze, ZHANG Chaoyang, HONG Fangjun, WANG Dahai. Heat transfer characteristics of ethylene glycol aqueous solution in slit channel under negative pressure [J]. Chemical Industry and Engineering Progress, 2023, 42(S1): 148-157.
[3]	CHEN Lin, XU Peiyuan, ZHANG Xiaohui, CHEN Jie, XU Zhenjun, CHEN Jiaxiang, MI Xiaoguang, FENG Yongchang, MEI Deqing. Investigation on the LNG mixed refrigerant flow and heat transfer characteristics in coil-wounded heat exchanger (CWHE) system [J]. Chemical Industry and Engineering Progress, 2023, 42(9): 4496-4503.
[4]	CHENG Tao, CUI Ruili, SONG Junnan, ZHANG Tianqi, ZHANG Yunhe, LIANG Shijie, PU Shi. Analysis of impurity deposition and pressure drop increase mechanisms in residue hydrotreating unit [J]. Chemical Industry and Engineering Progress, 2023, 42(9): 4616-4627.
[5]	BU Zhicheng, JIAO Bo, LIN Haihua, SUN Hongyuan. Review on computational fluid dynamics (CFD) simulation and advances in pulsating heat pipes [J]. Chemical Industry and Engineering Progress, 2023, 42(8): 4167-4181.
[6]	CHEN Weiyang, SONG Xin, YIN Yaran, ZHANG Xianming, ZHU Chunying, FU Taotao, MA Youguang. Effect of liquid viscosity on bubble interface in the rectangular microchannel [J]. Chemical Industry and Engineering Progress, 2023, 42(7): 3468-3477.
[7]	LIU Houli, GU Zhonghao, YANG Kang, ZHANG Li. Effect of groove width on pool boiling heat transfer characteristics in 3D printing groove structure [J]. Chemical Industry and Engineering Progress, 2023, 42(5): 2282-2288.
[8]	PANG Liping, YUAN Hu, QIU Wensheng, DUAN Liqiang, LI Wenxue. Hydrodynamic characteristics during peaking operation in utility boiler [J]. Chemical Industry and Engineering Progress, 2023, 42(4): 1708-1718.
[9]	ZHU Ge, BI Qincheng, TIAN Shujian, YAN Jianguo. Analysis of pressure drop characteristics of the cooling channel with twisted tape insert under high and non-uniform heat fluxes [J]. Chemical Industry and Engineering Progress, 2023, 42(10): 5083-5091.
[10]	JIA Wenlong, SUN Yibin, TANG Ding, CHEN Jiawen, LEI Siluo, LI Changjun. Intelligent recognition method for pressure drop signals of gas pipeline leakage based on support vector machine [J]. Chemical Industry and Engineering Progress, 2022, 41(9): 4713-4722.
[11]	ZHANG Meng, LI Shuqian, ZHANG Dong, MA Kunru. Motion characteristics for vapor-liquid interfaces of direct contact condensation in a microchannel [J]. Chemical Industry and Engineering Progress, 2022, 41(9): 4644-4652.
[12]	FENG Longlong, ZHONG Ke, ZHANG Yusen, SHANG Qingchun, JIA Hongwei. Flow boiling heat transfer characteristics of R1234yf in horizontal microchannel [J]. Chemical Industry and Engineering Progress, 2022, 41(7): 3502-3509.
[13]	MEI Xiang, YAO Yuanpeng, WU Huiying. Analysis of heat transfer enhancement mechanism on subcooled flow boiling in interconnected microchannels [J]. Chemical Industry and Engineering Progress, 2022, 41(6): 2884-2892.
[14]	YANG Honghai, ZHANG Miao, LIU Liwei, ZHOU Yi, SHEN Junjie, SHI Weigang, YIN Yong. Heat transfer performance enhancement and prediction in GO/water pulsating heat pipe [J]. Chemical Industry and Engineering Progress, 2022, 41(4): 1725-1734.
[15]	FAN Xiangru, YANG Yijin, GUO Xujing, ZHANG Quanbi. Study on the adsorption characteristics of methylene blue by soft manganese ore-oil sludge-based activated carbon [J]. Chemical Industry and Engineering Progress, 2022, 41(12): 6664-6671.