Influence of surface tension and viscosity on the start-up time and thermal resistance of pulsating heat pipe

doi:10.16085/j.issn.1000-6613.2016-2309

Chemical Industry and Engineering Progress ›› 2017, Vol. 36 ›› Issue (08): 2816-2821.DOI: 10.16085/j.issn.1000-6613.2016-2309

Previous Articles Next Articles

Influence of surface tension and viscosity on the start-up time and thermal resistance of pulsating heat pipe

ZHENG Kaiming, XU Rongji, WANG Ruixiang, XING Meibo, CAI Jichi, YUAN Ya

Beijing Engineering Research Centre of Sustainable Energy and Buildings, Beijing University of Civil Engineering and Architecture, Beijing 100044, China

Received:2016-12-13 Revised:2017-03-21 Online:2017-08-05 Published:2017-08-05

工质表面张力和黏度对脉动热管启动及传热热阻的影响

郑开明, 徐荣吉, 王瑞祥, 邢美波, 蔡骥驰, 苑亚

北京建筑大学北京市建筑能源高效综合利用工程技术研究中心, 北京 100044

通讯作者: 王瑞祥,教授,研究方向为制冷与空调系统热物理过程、纳米材料与工质技术。
作者简介:郑开明(1991-),男,硕士研究生,研究方向为制冷系统热物理过程。E-mail:zhengkaiming2015@163.com。
基金资助:
国家自然科学基金青年基金（51506004）及北京市自然科学基金（3162009）项目。

Abstract

Abstract: Thermo-physical properties of aqueous solutions of potassium perfluorooctanoate(PFOK),with mass fractions of 0.02%,0.05%,0.1%,0.2%,0.5%,were tested respectively. It was found that significant changes in a little amount of PFOK could lead to surface tension of water,viscosity followed,while the specific heat,density,thermal conductivity and other parameters of water were less affected. An experimental study on characteristics of the pulsating heat pipe(PHP),with the inner diameter of 2.5mm of copper pipe,using water of different surface tensions and viscosities was carried out. The results showed that promotion of heating power on startup time is obvious if the heating power input is no more than 60W. Change laws of startup time and thermal resistance with the effect of surface tension present "W" type image due to the increment of viscosity. Besides,the effect of surface tension and viscosity on the thermal resistance is decreased with the increase of the heating power.

Key words: pulsating heat pipe, surface tension, viscosity, startup time, thermal resistance

摘要： 以表面活性剂全氟辛酸钾（potassium perfluorooctanoate，PFOK）为溶质，以纯水为基液，配制了质量分数为0.02%、0.05%、0.1%、0.2%、0.5%共5种溶液并进行了物性测试，发现PFOK对水的表面张力改变较大，黏度其次，比热容、密度、热导率等参数影响较小；实验研究了不同表面张力及黏度工质对内径为2.5mm的脉动热管在不同加热功率下的启动时间和传热热阻的变化规律。结果表明：加热功率对启动时间的促进作用在≤ 60W时较为明显；由于黏度增加的影响，表面张力对启动时间及传热热阻的变化规律都呈现W形图像；并且随着加热功率的增加，表面张力和黏度对传热热阻的影响作用下降。

关键词: 脉动热管, 表面张力, 黏度, 启动时间, 传热热阻

CLC Number:

ZHENG Kaiming, XU Rongji, WANG Ruixiang, XING Meibo, CAI Jichi, YUAN Ya. Influence of surface tension and viscosity on the start-up time and thermal resistance of pulsating heat pipe[J]. Chemical Industry and Engineering Progress, 2017, 36(08): 2816-2821.

郑开明, 徐荣吉, 王瑞祥, 邢美波, 蔡骥驰, 苑亚. 工质表面张力和黏度对脉动热管启动及传热热阻的影响[J]. 化工进展, 2017, 36(08): 2816-2821.

References

[1] AKACHI H.Structure of a heat pipe:US 4921041[P].1990.
[2] 杨洪海,肖荪,GROLL M.工质热物性对脉动热管运行性能的影响[J].工程热物理学报,2010,31(1):97-99. YANG H H,XIAO S,GROLL M.Effect of thermo physical properties of working fluids on operational performance in pulsating heat pipes[J].Journal of Engineering Thermophysics,2010,31(1):97-99.
[3] 史维秀,李惟毅,潘利生.乙醇水溶液脉动热管传热特性研究[J].机械工程学报,2011,47(24):117-121. SHI W X,LI W Y,PAN L S.Study on heat transfer properties of aqueous ethanol pulsating heat pipe[J].Journal of Mechanical Engineering,2011,47(24):117-121.
[4] SHAFⅡ M B,FAGHRI A,ZHANG Y W.Thermal modeling of unlooped and looped pulsating heat pipes[J].ASME Journal of Heat Transfer,2002,123(6):1159-1172.
[5] SHAFⅡ M B,FAGHRI A,ZHANG Y W.Analysis of heat transfer in unlooped and looped pulsating heat pipes[J]. International Journal of Numerical Methods for Heat and Fluid Flow,2002,12(12):585-609.
[6] ZHANG Y W,FAGHRI A.Heat transfer in a pulsating heat pipe with open end[J].International Journal of Heat and Mass Transfer,2002,45(4):755-764.
[7] ZHANG X M,XU J L,ZHOU Z Q.Experimental study of a pulsating heat pipe using FC-72,ethanol,and water as working fluids[J].Experimental Heat Transfer,2004,17(1):47-67.
[8] 崔晓钰,王妍,翁建华,等.不同工质振荡热管的传热性能[J].上海理工大学学报,2009,31(6):539-543. CUI X Y,WANG Y,WENG J H,et al.Experimental study on pulsating heat pipe with different working fluids[J].Journal University of Shanghai for Science and Technology,2009,31(6):539-543.
[9] 崔晓钰,于洋,朱悦,等.振荡热管传热性能与工质物性关系分析[J].化工进展,2013,32(9):2035-2042. CUI X Y,YU Y,ZHU Y,et al.Correlation on physical properties of working fluids and heat transfer performance of pulsating heat pipes[J].Chemical Industry and Engineering Progress,2013,32(9):2035-2042.
[10] WANG X H,ZHENG H C,SI M Q,et al.Experimental investigation of the influence of surfactant on the heat transfer performance of pulsating heat pipe[J].International Journal of Heat and Mass Transfer,2015,83:586-590.
[11] 蔡骥驰,王瑞祥,徐荣吉,等.SDBS对铜-水脉动热管启动及传热性能影响[J]. 化工学报,2016,67(5):1852-1857. CAI J C,WANG R X,XU R J,et al.Influence of SDBS on start time and heat transfer performance of pulsating heat pipe[J].CIESC Journal,2016,67(5):1852-1857.
[12] IVEY H J.Relationships between bubble frequency, departure diameter and rise velocity in nucleate boiling[J].International Journal of Heat & Mass Transfer,1967,10(8):1023-1040.
[13] YANG H H,XIAO S,GROLL M.Effect of thermo physical properties of working fluids on operational performance in pulsating heat pipes[J].Journal of Engineering Thermophysics,2010,31(1):97-99.
[14] SHAFⅡ M B,FAGHRI A,ZHANG Y W.Thermal modeling of unlooped and looped pulsating heat pipes[J].Journal of Heat Transfer,2001,123(6):1159-1172.
[15] KHANDEKAR S,SCHNEIDER M,SCHAFER P,et al.Dynamic study of flat plate closed loop pulsating heat pipe[J].Microscale Thermo Physical Engineering,2002,6(4):303-317.

Influence of surface tension and viscosity on the start-up time and thermal resistance of pulsating heat pipe

工质表面张力和黏度对脉动热管启动及传热热阻的影响

PDF (PC)

Knowledge

Abstract

Cite this article

share this article

References

Related Articles 15

Recommended Articles

Metrics

Comments

[1]	HUI Bo, HOU Hongyi, ZHANG Tao, CHE Shengwen. Drying characteristics of cylindrical annular pulsating heat pipe [J]. Chemical Industry and Engineering Progress, 2023, 42(S1): 33-40.
[2]	XU Maoyu, TAO Shuai, QI Cong, LIANG Lin. Start-up and temperature fluctuation of loop heat pipe with flat disk evaporator [J]. Chemical Industry and Engineering Progress, 2023, 42(9): 4531-4537.
[3]	ZHANG Chao, YANG Peng, LIU Guanglin, ZHAO Wei, YANG Xufei, ZHANG Wei, YU Bo. Influence of surface microstructure on arrayed microjet flow boiling heat transfer [J]. Chemical Industry and Engineering Progress, 2023, 42(8): 4193-4203.
[4]	XIE Zhiwei, WU Zhangyong, ZHU Qichen, JIANG Jiajun, LIANG Tianxiang, LIU Zhenyang. Viscosity properties and magnetoviscous effects of Ni_0.5Zn_0.5Fe₂O₄ vegetable oil-based magnetic fluid [J]. Chemical Industry and Engineering Progress, 2023, 42(7): 3623-3633.
[5]	CHEN Weiyang, SONG Xin, YIN Yaran, ZHANG Xianming, ZHU Chunying, FU Taotao, MA Youguang. Effect of liquid viscosity on bubble interface in the rectangular microchannel [J]. Chemical Industry and Engineering Progress, 2023, 42(7): 3468-3477.
[6]	SUN Zhengnan, LI Hongjing, JING Guolin, ZHANG Funing, YAN Biao, LIU Xiaoyan. Application of EVA and its modified polymer in crude oil pour point depressant field [J]. Chemical Industry and Engineering Progress, 2023, 42(6): 2987-2998.
[7]	YU Junsheng, ZHU Ye, LI Qiankun, XU Shixuan, ZHANG Xinyang, WANG Cheng, QU Jian. Performance of pulsating heat pipe with rising and declining heat flux [J]. Chemical Industry and Engineering Progress, 2023, 42(3): 1178-1186.
[8]	LI Guangwen, HUA Qucheng, HUANG Zuoxin, DA Zhijian. Progress on polymethacrylate as viscosity index improvers for lube oil [J]. Chemical Industry and Engineering Progress, 2023, 42(3): 1562-1571.
[9]	YANG Juanjuan, HE Lin, HE Changqing, LI Xingang, SUI Hong. Treatment of oily sludge through multiphase compound conditioning and demulsification separation process [J]. Chemical Industry and Engineering Progress, 2023, 42(2): 614-623.
[10]	ZHU Qichen, WU Zhangyong, WANG Zhiqiang, JIANG Jiajun, LI Xiang. Sedimentation stability and viscosity properties of silicone oil-based magnetic nanofluid at low temperature [J]. Chemical Industry and Engineering Progress, 2023, 42(10): 5101-5110.
[11]	LI Lu, BAO Sui, ZHANG Liming, WANG Ran, TAO Zhenghong, YANG Xingxiang. Preparation and characterization of carrageenan-konjac gum hybrid gel for encapsulating fragrance [J]. Chemical Industry and Engineering Progress, 2022, 41(S1): 376-381.
[12]	ZHANG Xincheng, HE Lin, SUI Hong, LI Xingang. Demulsification process and enhancement by viscosity reduction for water-in-heavy oil emulsions [J]. Chemical Industry and Engineering Progress, 2022, 41(7): 3534-3544.
[13]	ZHENG Suzheng, LI Nanxi, DONG Deping. Experimental and numerical investigation of loop heat pipe with flat ceramic capillary wick [J]. Chemical Industry and Engineering Progress, 2022, 41(7): 3510-3518.
[14]	YANG Honghai, ZHANG Miao, LIU Liwei, ZHOU Yi, SHEN Junjie, SHI Weigang, YIN Yong. Heat transfer performance enhancement and prediction in GO/water pulsating heat pipe [J]. Chemical Industry and Engineering Progress, 2022, 41(4): 1725-1734.
[15]	WANG Shuai, ZHAO Jinzhu, WANG Rongyuan, CUI Kaixiang, JING Jiaqiang. New ideas of heavy oil flow drag reduction by emulsification and wetting coupling action [J]. Chemical Industry and Engineering Progress, 2021, 40(S2): 126-139.