Chemical Industry and Engineering Progress ›› 2023, Vol. 42 ›› Issue (5): 2282-2288.DOI: 10.16085/j.issn.1000-6613.2022-1211

• Chemical processes and equipment • Previous Articles     Next Articles

Effect of groove width on pool boiling heat transfer characteristics in 3D printing groove structure

LIU Houli(), GU Zhonghao, YANG Kang, ZHANG Li()   

  1. School of Mechanical and Power Engineering, East China University of Science and Technology, Shanghai 200237, China
  • Received:2022-06-29 Revised:2022-08-23 Online:2023-06-02 Published:2023-05-10
  • Contact: ZHANG Li

3D打印槽道结构槽宽对池沸腾传热特性的影响

刘厚励(), 顾中浩, 阳康, 张莉()   

  1. 华东理工大学机械与动力工程学院, 上海 200237
  • 通讯作者: 张莉
  • 作者简介:刘厚励(1990—),男,博士研究生,研究方向为多孔结构强化沸腾传热。E-mail:flyli5@126.com
  • 基金资助:
    国家自然科学基金(51776074)

Abstract:

Surface microstructure is an important means to enhance boiling heat transfer, and it is significant to study the influence of microstructure size on boiling heat transfer characteristics. In this paper, selective laser melting (SLM) technology was used to fabricate channel structure samples with different widths, and the experimental study of pool boiling heat transfer characteristics under atmospheric pressure was carried out. The results showed that compared with the smooth copper surface, the heat transfer coefficient (HTC) and critical heat flux (CHF) of the groove structure with the groove length of 2.3mm and the groove width of 0.5—2.3mm were significantly improved. CHF of channel structure first increased and then decreased with the increase of channel width, and HTC decreases with the increase of channel width. CHF reached a maximum of 331.5W/cm2 at a channel width of 0.9mm, which was 3 times that of a smooth copper surface, and the HTC was 1.7 times that of the smooth surface. Smaller channel widths increased the heat transfer area of the specimen, limited the bubble departure diameter, and then increased the bubble separation frequency, which was a key factor for HTC enhancement. The gas-liquid flow resistance limitation and hydrodynamic instability in the channel were the key control factors for CHF enhancement in channel structure.

Key words: heat transfer, pool boiling, phase change, 3D printing, gas-liquid flow, groove structure

摘要:

表面微结构化是强化沸腾传热的重要手段,研究微结构尺寸对沸腾传热特性的影响规律意义重大。本文采用选择性激光熔化技术(SLM)制备了不同宽度的槽道结构试样,并对其进行了常压下池沸腾传热特性实验研究。结果表明,相比于光滑铜面,槽长2.3mm,槽宽0.5~2.3mm槽道结构的传热系数(HTC)与临界热通量(CHF)均有显著提升。槽道结构的CHF随着槽道宽度的增大先增加后减小,HTC随着槽道宽度的增大而减小。槽道宽度为0.9mm时CHF达到最大值331.5W/cm2,为光滑铜面的3倍,同时HTC为光滑表面的1.7倍。较小的槽道宽度增加了试样的传热面积,限制了气泡脱离直径进而增加气泡的脱离频率,是HTC提升的关键因素;而槽道内气液流动阻力限制与水动力不稳定性,是槽道结构CHF提升的关键控制因素。

关键词: 传热, 池沸腾, 相变, 3D打印, 气液两相流, 槽道结构

CLC Number: 

京ICP备12046843号-2;京公网安备 11010102001994号
Copyright © Chemical Industry and Engineering Progress, All Rights Reserved.
E-mail: hgjz@cip.com.cn
Powered by Beijing Magtech Co. Ltd